EUVIMEDEUVIMED entdecken
Crossref

Multi-objective grey correlation analysis based on CFRP Helical Milling simulation model

Lan Zhou, Yunlong Wang, Guosheng An, Ruibiao Zhu, Guangqi Li, Rong Ma

The International Journal of Advanced Manufacturing Technology · 2024-11 · 135 (3-4) · 1565-1585

DOI: 10.1007/s00170-024-14419-5 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 10.10.2024. Verfasst von Lan Zhou und 5 weiteren Autor:innen. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 35 Literaturangaben. Gefördert von: the Major Special Projects of Gansu Province, National Natural Science Foundation of China.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Helical milling is widely used in aerospace as a key processing technology for Carbon fiber reinforced polymer (CFRP). However, the eccentric machining characteristics lead to an unusually complex pattern of cutting force and residual stress distribution on the work-piece during helical milling processing. Based on the Hashin failure criterion, a 3D FEM model of CFRP helical milling was built for analyzing the changing law of cutting force, then the three factors and three levels orthogonal tests were used to investigate the influence of machining parameters on the axial force, radial force, and minimum principal residual stress, finally, the multi-objective optimization based on grey correlation analysis was realized. The results showed that the errors of axial force and radial force obtained by simulation and experiment were 10.68% and 12.26%, respectively. The axial force and radial force were negatively correlated to the spindle speed, positively correlated to the axial cutting depth, and uncorrelated to the feed per tooth. The minimum principal residual stress was negatively correlated to the spindle speed, positively correlated to the feed per tooth, and uncorrelated to the axial cutting depth. The degree of influence on optimization of machining parameters was: spindle speed > axial cutting depth > feed per tooth. The corresponding average grey correlation degree differences were 0.280981, 0.216859, and 0.013422, respectively. The maximum value of grey correlation degree in the orthogonal test was 0.874372, and the corresponding optimal parameters combination was the spindle speed 8000 r/min, feed per tooth 0.03 mm/z, and axial cutting depth 0.2 mm/r.

Förderung

  • the Major Special Projects of Gansu Province
  • National Natural Science Foundation of China

Zitieren

APA

Zhou, L., Wang, Y., An, G., Zhu, R., Li, G., & Ma, R. (2024). Multi-objective grey correlation analysis based on CFRP Helical Milling simulation model. The International Journal of Advanced Manufacturing Technology, 135(3-4), 1565-1585. https://doi.org/10.1007/s00170-024-14419-5

Vancouver

Zhou L, Wang Y, An G, Zhu R, Li G, Ma R. Multi-objective grey correlation analysis based on CFRP Helical Milling simulation model. The International Journal of Advanced Manufacturing Technology. 2024;135(3-4):1565-1585. doi:10.1007/s00170-024-14419-5

BibTeX
@article{Zhou2024,
  author = {Zhou, Lan and Wang, Yunlong and An, Guosheng and Zhu, Ruibiao and Li, Guangqi and Ma, Rong},
  title = {Multi-objective grey correlation analysis based on CFRP Helical Milling simulation model},
  journal = {The International Journal of Advanced Manufacturing Technology},
  year = {2024},
  volume = {135},
  number = {3-4},
  pages = {1565--1585},
  doi = {10.1007/s00170-024-14419-5}
}
Kostenlos starten →