EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Electron beam powder bed fusion additive manufacturing of Ti6Al4V alloy lattice structures: orientation-dependent compressive strength and fracture behavior

Yawen Huang, Zhan Wen Chen, Antony Rey O. Wan, Kurt Schmidt, Peter Sefont, Saret Singamneni

The International Journal of Advanced Manufacturing Technology · 2024-06 · 132 (7-8) · 3299-3311

DOI: 10.1007/s00170-024-13539-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The International Journal of Advanced Manufacturing Technology, online erschienen am 09.04.2024. Verfasst von Yawen Huang und 5 weiteren Autor:innen. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Auckland University of Technology.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High porosity level lattice structures made using electron beam powder bed fusion additive manufacturing (EBPBF) need to be sufficiently strong and the understanding of the mechanical anisotropy of the structures is important for the design of orthopedic implants. In this work, the combined effects of loading direction (LD), cell orientation, and strut irregularity associated with EBPBF of Ti6Al4V alloy lattices on the mechanical behavior of the lattices under compressive loading have been studied. Three groups of simple cubic unit cell lattices were EBPBF made, compressively tested, and examined. The three groups were [001]//LD lattices, [011]//LD lattices, and [111]//LD lattices. Simulation has also been conducted. Yield strength (σ y-L ) values of all lattices determined experimentally have been found to be comparable to the values predicted by simulation; thus, EBPBF surface defects do not affect σ y-L . σ y-L of [001]//LD lattices is 1.8–2.0 times higher than those of [011]//LD and [111]//LD lattices. The reason for this is shown to be due to the high stress concentrations in non-[001]//LD samples, causing yielding at low loading levels. Furthermore, plastic strain (ε p ) at ultimate compression strength of [001]//LD samples has been determined to be 4–6 times higher than the values of non-[001]//LD samples. Examining the tested samples has shown cracks more readily propagating from EBPBF micro-notches in non-[001]//LD samples, resulting in low ε p .

Förderung

  • Auckland University of Technology

Zitieren

APA

Huang, Y., Chen, Z. W., Wan, A. R. O., Schmidt, K., Sefont, P., & Singamneni, S. (2024). Electron beam powder bed fusion additive manufacturing of Ti6Al4V alloy lattice structures: orientation-dependent compressive strength and fracture behavior. The International Journal of Advanced Manufacturing Technology, 132(7-8), 3299-3311. https://doi.org/10.1007/s00170-024-13539-2

Vancouver

Huang Y, Chen ZW, Wan ARO, Schmidt K, Sefont P, Singamneni S. Electron beam powder bed fusion additive manufacturing of Ti6Al4V alloy lattice structures: orientation-dependent compressive strength and fracture behavior. The International Journal of Advanced Manufacturing Technology. 2024;132(7-8):3299-3311. doi:10.1007/s00170-024-13539-2

BibTeX
@article{Huang2024,
  author = {Huang, Yawen and Chen, Zhan Wen and Wan, Antony Rey O. and Schmidt, Kurt and Sefont, Peter and Singamneni, Saret},
  title = {Electron beam powder bed fusion additive manufacturing of Ti6Al4V alloy lattice structures: orientation-dependent compressive strength and fracture behavior},
  journal = {The International Journal of Advanced Manufacturing Technology},
  year = {2024},
  volume = {132},
  number = {7-8},
  pages = {3299--3311},
  doi = {10.1007/s00170-024-13539-2}
}
Kostenlos starten →