EUVIMEDEUVIMED entdecken
Open Access

Comparing the effect of virtual and in-person instruction on students’ performance in a design for additive manufacturing learning activity

Anastasia M K Schauer iD, Kenton B Fillingim, Anna Pavleszek, Michael Chen, Katherine Fu iD

Research in Engineering Design · 2022-10 · 33 (4) · 385-394

DOI: 10.1007/s00163-022-00399-8 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Research in Engineering Design, online erschienen am 01.09.2022. Verfasst von Anastasia M K Schauer und 4 weiteren Autor:innen. Beteiligte Einrichtung: George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA USA. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: U.S. Department of Energy.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The goal of this work is to compare the outcome of a design for additive manufacturing (DfAM) heuristics lesson conducted in a virtual learning environment to the same in an in-person learning environment. Prior work revealed that receiving DfAM heuristics at different points in the design process impacts the quality and novelty of designs produced afterward, but this work may have been limited by the solely virtual format. In this work, an identical experiment was performed in a face-to-face learning environment. Results indicate that neither learning format presents an advantage over the other when it comes to the quality of designs produced during the intervention. Participants across all experimental groups reported an increase in self-efficacy after the intervention, with improved performance on quiz-type questions. However, the novelty and variety of the designs produced by the in-person experimental groups were significantly lower than that of the virtual experimental groups. In addition to validating the effectiveness of virtual instruction as a teaching method, these results also support the authors' hypothesis that the priming effect is stronger in an in-person classroom than in a virtual classroom.

Schlagwörter

Stichwörter der Autor:innen

Design for additive manufacturingEngineering educationVirtual learning

Autor:innen und Institutionen

  • George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA USA.
  • Oak Ridge National Laboratory, Manufacturing Science Division, Knoxville, TN USA.

ORCID-Profile: Anastasia M K Schauer, Katherine Fu

Förderung

  • U.S. Department of Energy

Zitieren

APA

Schauer, A. M. K., Fillingim, K. B., Pavleszek, A., Chen, M., & Fu, K. (2022). Comparing the effect of virtual and in-person instruction on students’ performance in a design for additive manufacturing learning activity. Research in Engineering Design, 33(4), 385-394. https://doi.org/10.1007/s00163-022-00399-8

Vancouver

Schauer AMK, Fillingim KB, Pavleszek A, Chen M, Fu K. Comparing the effect of virtual and in-person instruction on students’ performance in a design for additive manufacturing learning activity. Research in Engineering Design. 2022;33(4):385-394. doi:10.1007/s00163-022-00399-8

BibTeX
@article{Schauer2022,
  author = {Schauer, Anastasia M K and Fillingim, Kenton B and Pavleszek, Anna and Chen, Michael and Fu, Katherine},
  title = {Comparing the effect of virtual and in-person instruction on students’ performance in a design for additive manufacturing learning activity},
  journal = {Research in Engineering Design},
  year = {2022},
  volume = {33},
  number = {4},
  pages = {385--394},
  doi = {10.1007/s00163-022-00399-8}
}
Kostenlos starten →