EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Understanding the adhesion performance of glued laminated timber manufactured with Australian softwood and high-density hardwood species

A. Faircloth, B. P. Gilbert, C. Kumar, W. Leggate, R. L. McGavin

European Journal of Wood and Wood Products · 2024-12 · 82 (6) · 2013-2028

DOI: 10.1007/s00107-024-02138-3 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Wood and Wood Products, online erschienen am 13.09.2024. Verfasst von A. Faircloth und 4 weiteren Autor:innen. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Australian Centre for International Agricultural Research, State of Queensland acting through the Department of Agriculture and Fisheries.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To be commercialised, glued laminated timber must typically conform to a strict bond integrity assessment. While the associated testing protocols vary slightly from standard to standard, the general method consists of a series of swelling (water immersion) and shrinkage (drying) cycles. The approach is independent of the species and adhesive type. Those cycles strain the gluelines to a level depending on the species’ moisture uptake, timber dimensional movement and modulus of elasticity, as well as adhesive layer elasticity. High density and high modulus of elasticity materials frequently fail within the glueline regions rather than within the timber and therefore fail the bond integrity assessment. To better understand the mechanisms that lead to glueline failure, glulam samples were manufactured using three prominent Australian commercial timbers of various densities (Radiata pine— Pinus radiata , Southern pine— Pinus caribaea/Pinus elliottii , and Spotted gum— Corymbia citriodora ) and two structural adhesive types (resorcinol formaldehyde and polyurethane). Using advanced measurement techniques (digital image correlation and strain gauges), the response of the different species and adhesive types to moisture swelling and shrinkage, as well as times at which glueline separation occurs, were captured. A relationship was observed between moisture uptake and delamination percentages with spotted gum producing significantly higher levels of delamination and significantly lower moisture uptake values, compared to both Radiata pine and Southern pine. While the polyurethane glued samples on average produced higher levels of delamination, the digital image correlation data indicates that the time at which this delamination occurs is later than the samples glued with resorcinol formaldehyde.

Förderung

  • Australian Centre for International Agricultural Research
  • State of Queensland acting through the Department of Agriculture and Fisheries

Zitieren

APA

Faircloth, A., Gilbert, B. P., Kumar, C., Leggate, W., & McGavin, R. L. (2024). Understanding the adhesion performance of glued laminated timber manufactured with Australian softwood and high-density hardwood species. European Journal of Wood and Wood Products, 82(6), 2013-2028. https://doi.org/10.1007/s00107-024-02138-3

Vancouver

Faircloth A, Gilbert BP, Kumar C, Leggate W, McGavin RL. Understanding the adhesion performance of glued laminated timber manufactured with Australian softwood and high-density hardwood species. European Journal of Wood and Wood Products. 2024;82(6):2013-2028. doi:10.1007/s00107-024-02138-3

BibTeX
@article{Faircloth2024,
  author = {Faircloth, A. and Gilbert, B. P. and Kumar, C. and Leggate, W. and McGavin, R. L.},
  title = {Understanding the adhesion performance of glued laminated timber manufactured with Australian softwood and high-density hardwood species},
  journal = {European Journal of Wood and Wood Products},
  year = {2024},
  volume = {82},
  number = {6},
  pages = {2013--2028},
  doi = {10.1007/s00107-024-02138-3}
}
Kostenlos starten →