EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of thermal modification of wood particles for wood-PLA composites on properties of filaments, 3D-printed parts and injection moulded parts

Daša Krapež Tomec, Matthew Schwarzkopf, Rožle Repič, Jure Žigon, Bojan Gospodarič, Mirko Kariž

European Journal of Wood and Wood Products · 2024-04 · 82 (2) · 403-416

DOI: 10.1007/s00107-023-02018-2 ↗

Kurz gefasst

Fachartikel in der Zeitschrift European Journal of Wood and Wood Products, online erschienen am 09.12.2023. Verfasst von Daša Krapež Tomec und 5 weiteren Autor:innen. Die Arbeit wurde bisher 40-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Javna Agencija za Raziskovalno Dejavnost RS, European Commission.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper describes the development and characterisation of wood-filled polylactic acid (PLA) composite filaments for application in fused filament fabrication three-dimensional (3D) printing. Four different wood-polymer composite filaments for 3D printing were prepared, and specimens were 3D-printed with the obtained materials. The composite filaments consisted of wood particles (10% or 20% mass ratio) and a PLA polymer matrix. Wood particles were prepared by grinding and sieving non-modified beech wood and thermally modified (TM) (at 200 °C) beech wood. Thermal modification of wood affected particle preparation and smaller particles with lower aspect ratios were obtained. Filaments with TM wood particles were extruded better than with non-modified wood particles, with lower surface roughness and lower porosity. With a higher wood ratio, the surface roughness and porosity of the filament increased. Non-homogenous filaments also affected extrusion in 3D printing and reduced the properties of 3D-printed parts. Parts 3D-printed from filaments with TM particles had better tensile strength than from filaments with non-modified particles, but were lower than from pure PLA filaments. The tensile strength of the injection-moulded specimens was 18–69% higher than that of the 3D-printed specimens, depending on the filament composition. The results indicate some positive effects of thermal modification of wood particles on the properties of filaments and 3D-printed parts. Nevertheless, further optimisation of particle preparation and extrusion parameters is needed to obtain quality filaments with this size of wood particles.

Förderung

  • Javna Agencija za Raziskovalno Dejavnost RS
  • European Commission

Zitieren

APA

Tomec, D. K., Schwarzkopf, M., Repič, R., Žigon, J., Gospodarič, B., & Kariž, M. (2024). Effect of thermal modification of wood particles for wood-PLA composites on properties of filaments, 3D-printed parts and injection moulded parts. European Journal of Wood and Wood Products, 82(2), 403-416. https://doi.org/10.1007/s00107-023-02018-2

Vancouver

Tomec DK, Schwarzkopf M, Repič R, Žigon J, Gospodarič B, Kariž M. Effect of thermal modification of wood particles for wood-PLA composites on properties of filaments, 3D-printed parts and injection moulded parts. European Journal of Wood and Wood Products. 2024;82(2):403-416. doi:10.1007/s00107-023-02018-2

BibTeX
@article{Tomec2024,
  author = {Tomec, Daša Krapež and Schwarzkopf, Matthew and Repič, Rožle and Žigon, Jure and Gospodarič, Bojan and Kariž, Mirko},
  title = {Effect of thermal modification of wood particles for wood-PLA composites on properties of filaments, 3D-printed parts and injection moulded parts},
  journal = {European Journal of Wood and Wood Products},
  year = {2024},
  volume = {82},
  number = {2},
  pages = {403--416},
  doi = {10.1007/s00107-023-02018-2}
}
Kostenlos starten →