EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Gas‐Separating Metal‐Organic Framework Membrane Films on Large‐Area 3D‐Printed Tubular Ceramic Scaffolds

Surjakanta Rana, Roman Sajzew, Oksana Smirnova, Josef B. Slowik, Ayisha Komal, José Joaquin Velázquez, Ralf Wyrwa, Dušan Galusek, Ingolf Voigt, Lothar Wondraczek, Alexander Knebel

Small Structures · 2024-05 · 5 (5)

DOI: 10.1002/sstr.202300346 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small Structures, online erschienen am 19.02.2024. Verfasst von Surjakanta Rana und 10 weiteren Autor:innen. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 43 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Carl-Zeiss-Stiftung, Thüringer Aufbaubank, Horizon 2020 Framework Programme.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Polycrystalline metal‐organic framework (MOF) membrane films prepared on ceramic supports can separate gases with high energy efficiency. They generally exhibit very high permeance and selectivity but suffer from cost issues through the required ceramic supports. Increasing the area and reducing the ceramic component to a minimum can be a strategy to enabling neat membranes of MOFs. In a rapid prototyping approach using 3D‐printed porous scaffolds with a double‐helical channel geometry, an increased active membrane area‐to‐volume ratio is shown. Following stereolithographic printing and debinding of a ceramic slurry, an adapted sintering protocol is employed to sinter commercially available alumina slurries into porous scaffolds. The 3D‐printed scaffolds are optimized at a porosity of 40%, with satisfying mechanical stability. Furthermore, synthetic procedures yielding omnidirectional, homogeneous coatings on the outside and inside of the tubular scaffolds are developed. Membrane films of zeolitic imidazolate framework 8 and Hong Kong University of Science and Technology 1 covering a huge 50 cm 2 membrane area are produced in this way by applying a counter‐diffusion methodology. Gas‐separation performance is evaluated for H 2 , CO 2 , N 2 , and CH 4, in single‐gas measurements and on their binary‐gas mixtures.

Förderung

  • Carl-Zeiss-Stiftung
  • Thüringer Aufbaubank
  • Horizon 2020 Framework Programme

Zitieren

APA

Rana, S., Sajzew, R., Smirnova, O., Slowik, J. B., Komal, A., Velázquez, J. J., Wyrwa, R., Galusek, D., Voigt, I., Wondraczek, L., & Knebel, A. (2024). Gas‐Separating Metal‐Organic Framework Membrane Films on Large‐Area 3D‐Printed Tubular Ceramic Scaffolds. Small Structures, 5(5). https://doi.org/10.1002/sstr.202300346

Vancouver

Rana S, Sajzew R, Smirnova O, Slowik JB, Komal A, Velázquez JJ, et al. Gas‐Separating Metal‐Organic Framework Membrane Films on Large‐Area 3D‐Printed Tubular Ceramic Scaffolds. Small Structures. 2024;5(5). doi:10.1002/sstr.202300346

BibTeX
@article{Rana2024,
  author = {Rana, Surjakanta and Sajzew, Roman and Smirnova, Oksana and Slowik, Josef B. and Komal, Ayisha and Velázquez, José Joaquin and Wyrwa, Ralf and Galusek, Dušan and Voigt, Ingolf and Wondraczek, Lothar and Knebel, Alexander},
  title = {Gas‐Separating Metal‐Organic Framework Membrane Films on Large‐Area 3D‐Printed Tubular Ceramic Scaffolds},
  journal = {Small Structures},
  year = {2024},
  volume = {5},
  number = {5},
  doi = {10.1002/sstr.202300346}
}
Kostenlos starten →