Binary‐Solvent‐Programmed Single‐Step Inkjet Printing of Self‐Confined Micro‐Inlaid OLED Arrays
Small Methods · 2026-07 · 10 (14)
DOI: 10.1002/smtd.70769 ↗Kurz gefasst
Fachartikel in der Zeitschrift Small Methods, online erschienen am 15.06.2026. Verfasst von JaeWoo Park und 5 weiteren Autor:innen. Beteiligte Einrichtung: Materials Science and Engineering, Fulton Schools of Engineering, Arizona State University, Tempe, Arizona, USA. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 73 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Research Foundation of Korea, Kwangwoon University, Office of Naval Research (ONR).
Abstract (Originalsprache)
Inkjet printing offers a mask‐free route to large‐area electronics, yet achieving uniformity in micron‐scale organic light‐emitting diode (µ‐OLED) arrays remains challenging. Presented here is a photolithography‐free, solvent‐programmed, single‐step inkjet micro‐inlay process in which lateral phase separation self‐confines each emissive pixel. Guided by solubility parameters, a trichloromethane (TCM)/1,2‐dichloroethane (DCE) binary solvent is designed to optimize interactions among the solvents, emissive solutes, and the poly(4‐vinylpyridine) (P4VP) underlayer. Micro‐Raman mapping, cross‐sectional SEM, and AFM phase analysis support lateral phase separation between the emissive region and the displaced P4VP phase, selective restructuring of P4VP while preserving the underlying transport layer, and no detectable nanoscale phase segregation within the emissive interior, yielding self‐confined pixels of approximately 100 µm. High‐speed imaging shows that the blend yields reproducible 180 dpi arrays without jetting instability or nonuniform deposition. Green µ‐OLED arrays printed with the blend achieve a peak luminance of 2400 cd m −2 , a peak current efficiency of 3.5 cd A −1 , and a peak external quantum efficiency of 1.0%. The figure of merit and luminance uniformity improve by 2.6‐ and 6.9‐fold, and by 3.9‐ and 2.9‐fold, respectively, relative to neat TCM and neat DCE. This strategy enables scalable fabrication of flexible and three‐dimensional conformal OLED platforms.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Materials Science and Engineering, Fulton Schools of Engineering, Arizona State University, Tempe, Arizona, USA.
- Department of Plasma-Bio Display, Kwangwoon University, Seoul, South Korea.
- Department of Electrical and Biological Physics, Kwangwoon University, Seoul, South Korea.
ORCID-Profile: JaeWoo Park, Wonsun Kim, Kimin Lee, Sui Yang, Eun Ha Choi, Byoungchoo Park
Förderung
- National Research Foundation of Korea
- Kwangwoon University, Office of Naval Research (ONR)
Zitieren
APA
Park, J., Kim, W., Lee, K., Yang, S., Choi, E. H., & Park, B. (2026). Binary‐Solvent‐Programmed Single‐Step Inkjet Printing of Self‐Confined Micro‐Inlaid OLED Arrays. Small Methods, 10(14). https://doi.org/10.1002/smtd.70769
Vancouver
Park J, Kim W, Lee K, Yang S, Choi EH, Park B. Binary‐Solvent‐Programmed Single‐Step Inkjet Printing of Self‐Confined Micro‐Inlaid OLED Arrays. Small Methods. 2026;10(14). doi:10.1002/smtd.70769
BibTeX
@article{Park2026,
author = {Park, JaeWoo and Kim, Wonsun and Lee, Kimin and Yang, Sui and Choi, Eun Ha and Park, Byoungchoo},
title = {Binary‐Solvent‐Programmed Single‐Step Inkjet Printing of Self‐Confined Micro‐Inlaid OLED Arrays},
journal = {Small Methods},
year = {2026},
volume = {10},
number = {14},
doi = {10.1002/smtd.70769}
}
EUVIMED