EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Low‐Cost Ambient Pressure Drying Approach for Highly Porous Nanomaterial Structures

Erik Greve iD, Pia Pooker, Jan-Ole Stern iD, Rainer Adelung iD, Valeria Nicolosi iD, Dahnan Spurling iD

Small Methods · 2026-08 · 10 (15)

DOI: 10.1002/smtd.202502308 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small Methods, online erschienen am 20.04.2026. Verfasst von Erik Greve und 5 weiteren Autor:innen. Beteiligte Einrichtung: Functional Nanomaterials, Institute For Materials Science Faculty of Engineering, Kiel University, Kiel, Germany. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deutsche Forschungsgemeinschaft, HORIZON EUROPE European Innovation Council.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Drying highly porous structures presents a fundamental challenge, as capillary forces during evaporation collapse pores, limiting utility. Despite advances in sol–gel processing and nanostructure synthesis, techniques such as critical point drying (CPD) drive up cost, limit size and reduce throughput. This creates a major bottleneck for scalable fabrication of aerogels, membranes, and advanced lightweight materials. Here, a simple, low‐cost, solvent‐based technique for ambient temperature and pressure drying of highly porous graphene, MXene, PEDOT:PSS, MoS 2 , and TiO 2 structures is reported. The effectiveness of low surface tension solvents, hexamethyldisilizane and tetramethylsilane, are compared as drying media, while measurements of mass and volume during drying provide insight into the process. Using HMDS, capillary forces are minimized, and the microstructure of the materials is preserved. For example, shrinkage as low as 1.3% for graphene at an ultralow density of 0.018 g cm −3 was achieved. TMS showed inferior drying performance in direct comparison to HMDS due to its high vapor pressure and rapid evaporation. The use of low surface tension solvents also allowed the creation of large 11 × 11 cm graphene structures, greatly exceeding the chamber size of typical CPD equipment. Finally, a comparison of the cost of ambient drying and CPD is presented.

Schlagwörter

Stichwörter der Autor:innen

2D materialsaerogelambient dryingcritical point dryerdrying mechanismsnanomaterialsporous materials

Autor:innen und Institutionen

  • Functional Nanomaterials, Institute For Materials Science Faculty of Engineering, Kiel University, Kiel, Germany.
  • Centre for Research on Adaptive Nanostructures and Nanodevices (CRANN) & Advanced Materials Bio-Engineering Research Centre (AMBER), Trinity College Dublin, School of Chemistry, Dublin, Ireland.

ORCID-Profile: Erik Greve, Jan-Ole Stern, Rainer Adelung, Valeria Nicolosi, Dahnan Spurling

Förderung

  • Deutsche Forschungsgemeinschaft
  • HORIZON EUROPE European Innovation Council

Zitieren

APA

Greve, E., Pooker, P., Stern, J. O., Adelung, R., Nicolosi, V., & Spurling, D. (2026). Low‐Cost Ambient Pressure Drying Approach for Highly Porous Nanomaterial Structures. Small Methods, 10(15). https://doi.org/10.1002/smtd.202502308

Vancouver

Greve E, Pooker P, Stern JO, Adelung R, Nicolosi V, Spurling D. Low‐Cost Ambient Pressure Drying Approach for Highly Porous Nanomaterial Structures. Small Methods. 2026;10(15). doi:10.1002/smtd.202502308

BibTeX
@article{Greve2026,
  author = {Greve, Erik and Pooker, Pia and Stern, Jan-Ole and Adelung, Rainer and Nicolosi, Valeria and Spurling, Dahnan},
  title = {Low‐Cost Ambient Pressure Drying Approach for Highly Porous Nanomaterial Structures},
  journal = {Small Methods},
  year = {2026},
  volume = {10},
  number = {15},
  doi = {10.1002/smtd.202502308}
}
Kostenlos starten →