EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Printed Lateral p–n Junction for Thermoelectric Generation

Md Mofasser Mallick iD, Leonard Franke, Mohamed Hussein, Andres Georg Rösch, Zhongmin Long, Yolita Maria Eggeler, Uli Lemmer iD

Small Science · 2024-11 · 4 (11)

DOI: 10.1002/smsc.202400257 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small Science, online erschienen am 13.08.2024. Verfasst von Md Mofasser Mallick und 6 weiteren Autor:innen. Beteiligte Einrichtung: Light Technology Institute Karlsruhe Institute of Technology (KIT) 76131 Karlsruhe Germany. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Research Council, Deutsche Forschungsgemeinschaft, Deutsche Bundesstiftung Umwelt.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Printed thermoelectric generators (TEGs) show promising potential for converting waste heat into useful electricity at a low cost but fall short of exhibiting a conversion efficiency anticipated from materials’ properties. The output power of conventionally printed TEGs in the “π‐type” geometry suffers due to low thermal voltage and low current because of high thermal and electrical contact resistance, respectively. Herein, a type of printed p–n junction TEGs (PN‐TEGs) as a possible remedy is explored. Two printed PN‐TEGs with different thicknesses are fabricated using printed p‐type Bi 0.5 Sb 1.5 Te 3 and n‐type Bi 2 Te 2.7 Se 0.3 materials. The PN‐TEGs show a promising way to minimize the influence of thermal and electrical resistance in printed TEGs. In the experimental and simulation results, the significant impact of PN‐TEGs’ dimensions on their power outputs is revealed. Also, a conventional “π‐type” printed TEG is fabricated and its performance is studied. The optimized PN‐TEG with a single thermocouple yields ≈14 times higher power output density of 5.3 μW cm −2 at a Δ T of 25 K compared to “π‐type” printed TEGs.

Schlagwörter

Stichwörter der Autor:innen

COMSOLSeebeck effectsprinted thermoelectricsp–n junctionsthermoelectric generators

Autor:innen und Institutionen

  • Light Technology Institute Karlsruhe Institute of Technology (KIT) 76131 Karlsruhe Germany.
  • Institute of Microstructure Technology Karlsruhe Institute of Technology (KIT) 76344 Eggenstein-Leopoldshafen Germany.
  • Department of Physics Faculty of Science Ain Shams University Cairo 11566 Egypt.
  • Laboratory for Electron Microscopy Karlsruhe Institute of Technology (KIT) 76131 Karlsruhe Germany.

ORCID-Profile: Md Mofasser Mallick, Uli Lemmer

Förderung

  • European Research Council
  • Deutsche Forschungsgemeinschaft
  • Deutsche Bundesstiftung Umwelt
  • Horizon 2020 Framework Programme

Zitieren

APA

Mallick, M. M., Franke, L., Hussein, M., Rösch, A. G., Long, Z., Eggeler, Y. M., & Lemmer, U. (2024). Printed Lateral p–n Junction for Thermoelectric Generation. Small Science, 4(11). https://doi.org/10.1002/smsc.202400257

Vancouver

Mallick MM, Franke L, Hussein M, Rösch AG, Long Z, Eggeler YM, et al. Printed Lateral p–n Junction for Thermoelectric Generation. Small Science. 2024;4(11). doi:10.1002/smsc.202400257

BibTeX
@article{Mallick2024,
  author = {Mallick, Md Mofasser and Franke, Leonard and Hussein, Mohamed and Rösch, Andres Georg and Long, Zhongmin and Eggeler, Yolita Maria and Lemmer, Uli},
  title = {Printed Lateral p–n Junction for Thermoelectric Generation},
  journal = {Small Science},
  year = {2024},
  volume = {4},
  number = {11},
  doi = {10.1002/smsc.202400257}
}
Kostenlos starten →