EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Tailoring MXene Flake Morphology via Aerosol Jet Printing for Biological and Strain Sensor Applications

Javier Gutierrez-Gonzalez iD, Dahnan Spurling iD, Cian O'Connor iD, Eoin Caffrey iD, Tara McGuire, Jack Maughan iD, Tian Carey iD, Jose Munuera iD, Ilias M Oikonomou iD, Julian Carolan iD, Luke Doolan, Ian Woods iD und 7 weitere

Small · 2026

DOI: 10.1002/smll.75583 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small, 2026. Verfasst von Javier Gutierrez-Gonzalez und 18 weiteren Autor:innen. Beteiligte Einrichtung: Tissue Engineering Research Group, Department of Anatomy & Regenerative Medicine, Royal College of Surgeons in Ireland (RCSI), Dublin, Ireland. Hauptthemen laut MEDLINE: Printing, Titanium, Biosensing Techniques. Die Arbeit nennt 178 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: EPSRC/ Research Ireland Centre for Doctoral Training in the Advanced Characterization of Materials, Irish Rugby Football Union Charitable Trust (IRFU-CT), the Research Ireland Advanced Materials and Bioengineering Research (AMBER) Centre, European Commission - NextGenerationEU.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

MXenes (Ti 3 C 2 T x ) are two‐dimensional (2D) layered nanomaterials typically processed as aligned flakes. However, their morphology can also be engineered into crumpled architectures with distinct physicochemical properties that remain largely unexplored. Here, Aerosol Jet Printing (AJP) is established as a scalable manufacturing strategy to tailor MXene flake morphology through precise control of the printing conditions. By repurposing the printer's built‐in alignment camera, a rapid monitoring method was developed to distinguish aligned and crumpled morphologies during fabrication. Systematic investigation of the printing parameters identified mass flow, nozzle size, and ink concentration as the key variables governing flake morphology, demonstrating its general applicability on other 2D materials, such as graphene and MoS 2 . Aligned MXene films achieved electrical conductivities of up to 2672 ± 125 S cm − 1 , whereas crumpled films exhibited increased roughness and hydrophilicity. The engineered morphologies were further validated across multiple applications, including neural interfaces, antimicrobial coatings, and strain sensors. Both morphologies supported excellent biocompatibility with primary neurons and human induced pluripotent stem cell‐derived neural cells, while crumpled MXenes enhanced antibacterial activity against Staphylococcus aureus and improved strain‐sensing performance. These findings highlight the importance of controlling the morphology of 2D materials during 3D printing, providing a scalable route toward multifunctional biomedical devices.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PrintingTitaniumBiosensing TechniquesHumansAerosolsPrinting, Three-DimensionalAnimalsNitritesTransition Elements

Stichwörter der Autor:innen

2D materials3D printingMXenesantimicrobialbiocompatibilityneural interfacesstrain sensing

Substanzen

AerosolsTitaniumMXeneNitritesTransition Elements

Autor:innen und Institutionen

  • Tissue Engineering Research Group, Department of Anatomy & Regenerative Medicine, Royal College of Surgeons in Ireland (RCSI), Dublin, Ireland.
  • Advanced Materials and Bioengineering Research (AMBER) Centre RCSI, Dublin, Ireland.
  • School of Chemistry, Centre for Research on Adaptive Nanostructures and Nanodevices (CRANN) & Advanced Materials Bio-Engineering Research Centre (AMBER), Trinity College Dublin, Dublin, Ireland.
  • School of Physics, Trinity College Dublin (TCD), University of Dublin, Dublin, Ireland.
  • Instituto de Ciencia y Tecnología del Carbono, INCAR-CSIC, Oviedo, Spain.
  • Chair of Theoretical Chemistry, TU Dresden, Dresden, Germany.

ORCID-Profile: Javier Gutierrez-Gonzalez, Dahnan Spurling, Cian O'Connor, Eoin Caffrey, Jack Maughan, Tian Carey, Jose Munuera, Ilias M Oikonomou, Julian Carolan, Ian Woods, Giulio Brunetti, Maeve A Caldwell, Richard G Hobbs, Valeria Nicolosi, Fergal J O'Brien

Förderung

  • EPSRC/ Research Ireland Centre for Doctoral Training in the Advanced Characterization of Materials
  • Irish Rugby Football Union Charitable Trust (IRFU-CT), the Research Ireland Advanced Materials and Bioengineering Research (AMBER) Centre
  • European Commission - NextGenerationEU
  • Royal Society-Research Ireland University Research Fellowship

Zitieren

APA

Gutierrez-Gonzalez, J., Spurling, D., O'Connor, C., Caffrey, E., McGuire, T., Maughan, J., Carey, T., Munuera, J., Oikonomou, I. M., Carolan, J., Doolan, L., Woods, I., Brunetti, G., Caldwell, M. A., Dervan, A., Hobbs, R. G., Coleman, J. N., Nicolosi, V., & O'Brien, F. J. (2026). Tailoring MXene Flake Morphology via Aerosol Jet Printing for Biological and Strain Sensor Applications. Small. https://doi.org/10.1002/smll.75583

Vancouver

Gutierrez-Gonzalez J, Spurling D, O'Connor C, Caffrey E, McGuire T, Maughan J, et al. Tailoring MXene Flake Morphology via Aerosol Jet Printing for Biological and Strain Sensor Applications. Small. 2026. doi:10.1002/smll.75583

BibTeX
@article{GutierrezGonzalez2026,
  author = {Gutierrez-Gonzalez, Javier and Spurling, Dahnan and O'Connor, Cian and Caffrey, Eoin and McGuire, Tara and Maughan, Jack and Carey, Tian and Munuera, Jose and Oikonomou, Ilias M and Carolan, Julian and Doolan, Luke and Woods, Ian and Brunetti, Giulio and Caldwell, Maeve A and Dervan, Adrian and Hobbs, Richard G and Coleman, Jonathan N and Nicolosi, Valeria and O'Brien, Fergal J},
  title = {Tailoring MXene Flake Morphology via Aerosol Jet Printing for Biological and Strain Sensor Applications},
  journal = {Small},
  year = {2026},
  doi = {10.1002/smll.75583}
}
Kostenlos starten →