EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

High Entropy Layered Cathode With Single Grain Morphology for High‐Performance Sodium‐Ion Batteries

Daniele Callegari iD, Giulia Maranini, Claudia Triolo iD, Mariam Maisuradze iD, Hemanth Kumar Beere, Abdelhaq Nassiri, Umberto Anselmi-Tamburini iD, Saveria Santangelo iD, Marco Giorgetti iD, Mauro Coduri iD

Small · 2026-02 · 22 (11)

DOI: 10.1002/smll.202511833 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small, online erschienen am 15.01.2026. Verfasst von Daniele Callegari und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, University of Pavia, Pavia, Italy. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: OPerando studies of High-Entropy oxide-based active materials for Na-Ion battery cathodes, European Union-NextGenerationEU, University of Pavia through the program.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A major obstacle in the advancement of sodium‐ion batteries (SIBs) is the development of cathode active materials (CAMs) that offer both high specific capacity and long‐term cycling stability. Among the various candidates, layered CAMs have attracted significant attention. In this work, we synthesized a high‐entropy layered CAM with composition (Na 0.52 Ti 0.19 Mn 0.19 Fe 0.21 Ni 0.21 Co 0.20 O 2 ) using a spray pyrolysis technique, yielding large (0.75 µm on average) and separated grains. The resulting material comprises a P3–O3 layered oxide mixture, along with ∼20% rock‐salt and spinel phases. This CAM demonstrates a high specific capacity (∼180 mAh g −1 at 0.08 C), excellent rate capability (69% retention after 300 cycles at 1C), and high coulombic efficiency (>99.5%). In comparison, a CAM of identical composition synthesized via a conventional sol–gel method, exhibiting an agglomerated microstructure, showed lower capacity and retention, consistent with literature reports. These findings highlight the advantages of combining high entropy design and cathode morphology in developing next‐generation cathodes for SIBs.

Schlagwörter

Stichwörter der Autor:innen

high entropy oxidelayered cathode materialssodium ion batteriesspray‐pyrolysis

Autor:innen und Institutionen

  • Department of Chemistry, University of Pavia, Pavia, Italy.
  • INSTM, Firenze, Italy.
  • Department of Civil, Energy, Environmental and Materials Engineering (DICEAM), Mediterranean University, Reggio Calabria, Italy.
  • National Reference Center for Electrochemical Energy Storage (GISEL), Firenze, Italy.
  • Department of Industrial Chemistry "Toso Montanari", University of Bologna, Bologna, Italy.

ORCID-Profile: Daniele Callegari, Claudia Triolo, Mariam Maisuradze, Umberto Anselmi-Tamburini, Saveria Santangelo, Marco Giorgetti, Mauro Coduri

Förderung

  • OPerando studies of High-Entropy oxide-based active materials for Na-Ion battery cathodes
  • European Union-NextGenerationEU
  • University of Pavia through the program

Zitieren

APA

Callegari, D., Maranini, G., Triolo, C., Maisuradze, M., Beere, H. K., Nassiri, A., Anselmi-Tamburini, U., Santangelo, S., Giorgetti, M., & Coduri, M. (2026). High Entropy Layered Cathode With Single Grain Morphology for High‐Performance Sodium‐Ion Batteries. Small, 22(11). https://doi.org/10.1002/smll.202511833

Vancouver

Callegari D, Maranini G, Triolo C, Maisuradze M, Beere HK, Nassiri A, et al. High Entropy Layered Cathode With Single Grain Morphology for High‐Performance Sodium‐Ion Batteries. Small. 2026;22(11). doi:10.1002/smll.202511833

BibTeX
@article{Callegari2026,
  author = {Callegari, Daniele and Maranini, Giulia and Triolo, Claudia and Maisuradze, Mariam and Beere, Hemanth Kumar and Nassiri, Abdelhaq and Anselmi-Tamburini, Umberto and Santangelo, Saveria and Giorgetti, Marco and Coduri, Mauro},
  title = {High Entropy Layered Cathode With Single Grain Morphology for High‐Performance Sodium‐Ion Batteries},
  journal = {Small},
  year = {2026},
  volume = {22},
  number = {11},
  doi = {10.1002/smll.202511833}
}
Kostenlos starten →