Tailoring Composite Microstructure Through Milling for Dry‐Processed Sulfide‐Based Solid‐State Battery Cathodes
Small · 2025-10 · 21 (41)
DOI: 10.1002/smll.202507279 ↗Kurz gefasst
Fachartikel in der Zeitschrift Small, online erschienen am 05.09.2025. Verfasst von Finn Frankenberg und 10 weiteren Autor:innen. Beteiligte Einrichtung: Technische Universität Braunschweig, Institute for Particle Technology, Volkmaroder Straße 5, 38104, Braunschweig, Lower Saxony, Germany. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 83 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deutsche Forschungsgemeinschaft.
Abstract (Originalsprache)
While the effects of new solid electrolytes and active materials in cathode composites for solid‐state batteries are being intensively researched, little is known about the influence of mechanical processing on the properties of these composites. Here, the influence of mechanical process parameters on the production of Li 6 PS 5 Cl and LiNi 0.83 Co 0.11 Mn 0.06 O 2 composite cathodes applying a planetary ball milling process is systematically investigated. It is shown that the milling process has a significant influence on the microstructure of the composite by affecting the solid electrolyte particle size and the formation of electrolyte‐active material aggregates. The combination of experimental results with discrete element simulations shows that changes in microstructure with increasing energy input result in an increase in the density of heterocontacts, which improves the electrochemical performance. However, if the energy input is too high, a decrease in the crystallite size of Li 6 PS 5 Cl and an increase in strain in LiNi 0.83 Co 0.11 Mn 0.06 O 2 have a negative impact on the electrochemical performance. Subsequent dry film production of the pre‐milled composites reveals that a non‐optimized composite can be partially compensated by the high shear stresses acting during dry film production. Overall, the paramount importance of precisely controlling the milling process for the production of cathode composites is demonstrated.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Technische Universität Braunschweig, Institute for Particle Technology, Volkmaroder Straße 5, 38104, Braunschweig, Lower Saxony, Germany.
- Justus-Liebig-Universität Gießen, Institute of Physical Chemistry & Center for Materials Research, Heinrich-Buff-Ring 17, Hesse, 35392, Gießen, Germany.
- Forschungszentrum Jülich GmbH, Institute of Energy Materials and Devices (IMD), IMD 4: Helmholtz-Institut Münster Ionics in Energy Storage, 48149, Münster, North Rhine-Westphalia, Germany.
- Universität Münster, Institute of Inorganic and Analytical Chemistry, Corrensstraße 28-30, 48149, Münster, North Rhine-Westphalia, Germany.
ORCID-Profile: Finn Frankenberg, Carina A Heck, Maximilian Kissel, Peter Michalowski, Wolfgang G Zeier, Jürgen Janek, Arno Kwade
Förderung
- Deutsche Forschungsgemeinschaft
Zitieren
APA
Frankenberg, F., Heck, C. A., Kissel, M., Lange, M. A., Faka, V., Diener, A., Haase, P., Michalowski, P., Zeier, W. G., Janek, J., & Kwade, A. (2025). Tailoring Composite Microstructure Through Milling for Dry‐Processed Sulfide‐Based Solid‐State Battery Cathodes. Small, 21(41). https://doi.org/10.1002/smll.202507279
Vancouver
Frankenberg F, Heck CA, Kissel M, Lange MA, Faka V, Diener A, et al. Tailoring Composite Microstructure Through Milling for Dry‐Processed Sulfide‐Based Solid‐State Battery Cathodes. Small. 2025;21(41). doi:10.1002/smll.202507279
BibTeX
@article{Frankenberg2025,
author = {Frankenberg, Finn and Heck, Carina A and Kissel, Maximilian and Lange, Martin A and Faka, Vasiliki and Diener, Alexander and Haase, Philipp and Michalowski, Peter and Zeier, Wolfgang G and Janek, Jürgen and Kwade, Arno},
title = {Tailoring Composite Microstructure Through Milling for Dry‐Processed Sulfide‐Based Solid‐State Battery Cathodes},
journal = {Small},
year = {2025},
volume = {21},
number = {41},
doi = {10.1002/smll.202507279}
}
EUVIMED