EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Evolution of Pore Volume During Stripping of Lithium Metal in Solid‐State Batteries Observed with Operando Dilatometry

Thomas A Schall iD, Till Fuchs iD, Janis K Eckhardt iD, Tim Klunz, Boris Mogwitz, Joachim Sann iD, Klaus Peppler iD, Jürgen Janek iD

Small · 2025-08 · 21 (33)

DOI: 10.1002/smll.202505053 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small, online erschienen am 25.06.2025. Verfasst von Thomas A Schall und 7 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Physical Chemistry, Justus-Liebig-University Giessen, Heinrich-Buff-Ring 17, D-35392, Giessen, Germany. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 63 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bundesministerium für Bildung und Forschung, ALANO, LiSI2.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Lithium metal solid‐state batteries are prone to pore formation at the interface between the metal anode and the solid electrolyte during discharge, when the applied current density exceeds the lithium vacancy diffusion rate in the metal. This leads to contact loss and eventually battery failure. To better understand the mechanisms of pore formation at the anode interface, operando information on the total pore volume is essential. In this study, a dedicated dilatometric measurement setup for operando tracking of pore volume is presented and validated. The working principle of this method is demonstrated in a case study on symmetric lithium‐garnet cells. The combination of the dilatometric data with galvanostatic electrochemical impedance spectroscopy (GEIS) allows for a systematic study of pore formation in any metal solid‐state battery. To quantify this process, the vacancy injection ratio is introduced, as a measure of the fraction of lithium atom sites that remain empty during stripping. These experimental results reveal that, under the conditions applied, pore formation begins immediately upon stripping, even before becoming detectable by GEIS. Furthermore, it is shown that pores initially grow laterally near the surface before deepening at later stages. Based on these findings, a pore formation and growth mechanism is proposed.

Schlagwörter

Stichwörter der Autor:innen

dilatometrylithium metal anodepore formationsolid‐state batteryvacancy injection ratio

Autor:innen und Institutionen

  • Institute of Physical Chemistry, Justus-Liebig-University Giessen, Heinrich-Buff-Ring 17, D-35392, Giessen, Germany.
  • Center for Materials Research (ZfM), Justus-Liebig-University Giessen, Heinrich-Buff-Ring 16, D-35392, Giessen, Germany.

ORCID-Profile: Thomas A Schall, Till Fuchs, Janis K Eckhardt, Joachim Sann, Klaus Peppler, Jürgen Janek

Förderung

  • Bundesministerium für Bildung und Forschung
  • ALANO
  • LiSI2
  • SilKompAs
  • Hessian State Ministry of Higher Education, Research, and the Arts (HMWK)

Zitieren

APA

Schall, T. A., Fuchs, T., Eckhardt, J. K., Klunz, T., Mogwitz, B., Sann, J., Peppler, K., & Janek, J. (2025). Evolution of Pore Volume During Stripping of Lithium Metal in Solid‐State Batteries Observed with Operando Dilatometry. Small, 21(33). https://doi.org/10.1002/smll.202505053

Vancouver

Schall TA, Fuchs T, Eckhardt JK, Klunz T, Mogwitz B, Sann J, et al. Evolution of Pore Volume During Stripping of Lithium Metal in Solid‐State Batteries Observed with Operando Dilatometry. Small. 2025;21(33). doi:10.1002/smll.202505053

BibTeX
@article{Schall2025,
  author = {Schall, Thomas A and Fuchs, Till and Eckhardt, Janis K and Klunz, Tim and Mogwitz, Boris and Sann, Joachim and Peppler, Klaus and Janek, Jürgen},
  title = {Evolution of Pore Volume During Stripping of Lithium Metal in Solid‐State Batteries Observed with Operando Dilatometry},
  journal = {Small},
  year = {2025},
  volume = {21},
  number = {33},
  doi = {10.1002/smll.202505053}
}
Kostenlos starten →