Fabricating Microstructures on Freeform Surfaces via Flexible Hydrogel Micromolds
Small · 2025-03 · 21 (11)
DOI: 10.1002/smll.202411751 ↗Kurz gefasst
Fachartikel in der Zeitschrift Small, online erschienen am 12.02.2025. Verfasst von Pang Zhu und 5 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory of Process Technology, NeptunLab, Department of Microsystems Engineering (IMTEK), Albert Ludwig University of Freiburg, 79110, Freiburg, G…. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 30 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Interactive and Programmable Materials, Carl Zeiss Foundation, H2020 European Research Council.
Abstract (Originalsprache)
Fabricating microstructures on curved surfaces is of great importance in several engineering fields, and it is an ongoing challenge to develop technologies that do not require complicated devices and cumbersome procedures. A novel approach is presented for fabricating microstructures with different topographies on curved surfaces using flexible microstructured hydrogels as molds. The hydrogel film is first microstructured via spatially controlled ultraviolet illumination utilizing its photo‐responsive property. The microstructured hydrogel film is then transferred to a desired surface. Due to its low modulus, the hydrogel film can be adapted to the curved surfaces including semi‐cylindrical and semi‐spherical surfaces as well as freeform surfaces with both convex and concave features. The final freeform surfaces with microstructures are obtained by polydimethylsiloxane (PDMS) casting. The resulting microstructures show high uniformity and high surface smoothness with an average roughness (Ra) ≈2.7 nm and a root mean square roughness (Rq) ≈4.1 nm. The ability to fabricate microstructures on large‐area curved surfaces of ≈4.5 cm by 6.5 cm is demonstrated. Finally, it is shown that the fabricated microstructures allow good imaging performance. This method utilizes the hydrogel's photo‐responsive ability to construct flexible molds and flexibility to adapt to freeform surfaces, thereby allowing significantly simplified fabrication processes.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Laboratory of Process Technology, NeptunLab, Department of Microsystems Engineering (IMTEK), Albert Ludwig University of Freiburg, 79110, Freiburg, Germany.
- Freiburg Materials Research Center (FMF), Albert Ludwig University of Freiburg, 79104, Freiburg, Germany.
- Freiburg Center of Interactive Materials and Bioinspired Technologies (FIT), Albert Ludwig University of Freiburg, 79110, Freiburg, Germany.
- Glassomer GmbH, 79110, Freiburg, Germany.
ORCID-Profile: Pang Zhu, Zahra Hosneolfat, Niloofar Nekoonam, Sagar Bhagwat, Dorothea Helmer, Bastian E Rapp
Förderung
- Interactive and Programmable Materials
- Carl Zeiss Foundation
- H2020 European Research Council
- Deutsche Forschungsgemeinschaft
- Carl-Zeiss-Stiftung
Zitieren
APA
Zhu, P., Hosneolfat, Z., Nekoonam, N., Bhagwat, S., Helmer, D., & Rapp, B. E. (2025). Fabricating Microstructures on Freeform Surfaces via Flexible Hydrogel Micromolds. Small, 21(11). https://doi.org/10.1002/smll.202411751
Vancouver
Zhu P, Hosneolfat Z, Nekoonam N, Bhagwat S, Helmer D, Rapp BE. Fabricating Microstructures on Freeform Surfaces via Flexible Hydrogel Micromolds. Small. 2025;21(11). doi:10.1002/smll.202411751
BibTeX
@article{Zhu2025,
author = {Zhu, Pang and Hosneolfat, Zahra and Nekoonam, Niloofar and Bhagwat, Sagar and Helmer, Dorothea and Rapp, Bastian E},
title = {Fabricating Microstructures on Freeform Surfaces via Flexible Hydrogel Micromolds},
journal = {Small},
year = {2025},
volume = {21},
number = {11},
doi = {10.1002/smll.202411751}
}
EUVIMED