EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Mechanically Stable Algal Biochar‐Alginate Hydrogels as Bio‐Based Adsorbents for Resource‐Efficient Heavy Metal Removal

Vajiheh Akbarzadeh, Muhammad Umar, Sruthi Udayakumar, Ghulam Rashid, Joudi Zarzour, Eric Evans, Elham H. Fini

SPE Polymers · 2026-07 · 7 (3)

DOI: 10.1002/pls2.70057 ↗

Kurz gefasst

Fachartikel in der Zeitschrift SPE Polymers, online erschienen am 25.07.2026. Verfasst von Vajiheh Akbarzadeh und 6 weiteren Autor:innen. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Qatar Research, Development and Innovation Council.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Bio‐based materials that valorize waste streams while enabling resource conservation are central to advancing circular and sustainable environmental solutions. This study reports the development of ionically crosslinked biochar‐encapsulated hydrogels (Bio‐H) as sustainable adsorbents for the removal of heavy metals from contaminated water systems. Cyanidioschyzon merolae ‐derived biochar, produced by hydrothermal liquefaction of biomass was incorporated into calcium‐crosslinked sodium alginate using a two‐step gelation process, creating a multifunctional, biodegradable composite. Swelling behavior demonstrated that biochar incorporation significantly reduced the initial contraction observed in pristine alginate hydrogels and enabled continuous, monotonic swelling, achieving equilibrium swelling ratios of 1.16 within 7 h, substantially faster than pristine systems. The mechanical integrity of the Bio‐H was assessed by dynamic mechanical analysis (DMA). The storage modulus (G′) exceeded the loss modulus (G″) across the entire 0.1–100 Hz range with no crossover, reaching a plateau of about 372 kPa, confirming a stable, elastically dominant crosslinked network. Scanning electron microscopy revealed an open macroporous network that became textured with particulate deposits after adsorption, with EDS confirming Cu and Fe uptake. Batch adsorption experiments showed that maximum adsorption capacities were achieved at pH 4 and 298 K. The maximum equilibrium adsorption capacity for Cu 2+ was 136 mg/g, whereas for Fe 3+ , the adsorption capacity was observed to be 1.25 mg/g. The M 5 model suggests that the adsorption of both metals proceeds through a physical multilayer mechanism, which involves heterogeneous binding sites and sequential stacking of metal ions. The Bio‐H still removed the metal ions after the 3rd cycle of adsorption‐regeneration.

Förderung

  • Qatar Research, Development and Innovation Council

Zitieren

APA

Akbarzadeh, V., Umar, M., Udayakumar, S., Rashid, G., Zarzour, J., Evans, E., & Fini, E. H. (2026). Mechanically Stable Algal Biochar‐Alginate Hydrogels as Bio‐Based Adsorbents for Resource‐Efficient Heavy Metal Removal. SPE Polymers, 7(3). https://doi.org/10.1002/pls2.70057

Vancouver

Akbarzadeh V, Umar M, Udayakumar S, Rashid G, Zarzour J, Evans E, et al. Mechanically Stable Algal Biochar‐Alginate Hydrogels as Bio‐Based Adsorbents for Resource‐Efficient Heavy Metal Removal. SPE Polymers. 2026;7(3). doi:10.1002/pls2.70057

BibTeX
@article{Akbarzadeh2026,
  author = {Akbarzadeh, Vajiheh and Umar, Muhammad and Udayakumar, Sruthi and Rashid, Ghulam and Zarzour, Joudi and Evans, Eric and Fini, Elham H.},
  title = {Mechanically Stable Algal Biochar‐Alginate Hydrogels as Bio‐Based Adsorbents for Resource‐Efficient Heavy Metal Removal},
  journal = {SPE Polymers},
  year = {2026},
  volume = {7},
  number = {3},
  doi = {10.1002/pls2.70057}
}
Kostenlos starten →