EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Metal Oxide Fillers on the Thermo‐Mechanical and Physical Properties of Kenaf–Carbon Fiber Epoxy Hybrid Composites

Ishrak Ibn Zahid, Titu Nath, Nayan Sur, Arup Kumar Debnath, Md. Abdul Hasib

SPE Polymers · 2026-04 · 7 (2)

DOI: 10.1002/pls2.70043 ↗

Kurz gefasst

Fachartikel in der Zeitschrift SPE Polymers, online erschienen am 11.03.2026. Verfasst von Ishrak Ibn Zahid und 4 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study analyzes the effect of MgO, Al 2 O 3 , and TiO 2 metal oxide fillers on the physico‐mechanical and thermal behavior of kenaf/carbon fiber‐reinforced epoxy hybrid composites. Pb 3 O 4 ‐treated kenaf fibers were combined with carbon fiber mats to create a kenaf–carbon–kenaf (KCK) layered system, fabricated using the hand lay‐up method. Metal oxide fillers were added at concentrations of 1% and 2% to examine their effects on mechanical and physical properties. The tensile test results revealed that the 2% MgO delivered the highest strength of 93.74 MPa, surpassing the control sample (91.3 MPa) and also outperforming the Al 2 O 3 and TiO 2 incorporated sample. Flexural strength reached the maximum of 128.28 MPa with 2% of MgO, which is 41.98% higher than that of the control sample (90.35 MPa). The maximum impact strength was obtained at 2% Al 2 O 3 at 56.4 KJ/m 2 , a 37.46% increase from the control sample (41.03 KJ/m 2 ). In terms of moisture resistance, 2% TiO 2 demonstrated the best performance, showing the lowest water absorption. Additionally, the inclusion of metal oxide fillers improved the thermal properties. The higher diffusivity of 2% TiO 2 (0.198 mm 2 /s) and MgO (0.191 mm 2 /s) with lower volumetric specific heat (1.24 MJ/m 3 ·K) indicates rapid heat transfer, whereas the lower diffusivity of Al 2 O 3 (0.147 mm 2 /s) and the control (0.116 mm 2 /s) with higher volume specific heat favors insulation performance. Al 2 O 3 at 2% provides high thermal conductivity while maintaining moderate heat retention. Morphological analysis revealed that 2 wt.% MgO incorporated samples had good fiber‐matrix adhesion, but increased Al 2 O 3 and TiO 2 loadings had voids and agglomeration.

Zitieren

APA

Zahid, I. I., Nath, T., Sur, N., Debnath, A. K., & Hasib, M. A. (2026). Effect of Metal Oxide Fillers on the Thermo‐Mechanical and Physical Properties of Kenaf–Carbon Fiber Epoxy Hybrid Composites. SPE Polymers, 7(2). https://doi.org/10.1002/pls2.70043

Vancouver

Zahid II, Nath T, Sur N, Debnath AK, Hasib MA. Effect of Metal Oxide Fillers on the Thermo‐Mechanical and Physical Properties of Kenaf–Carbon Fiber Epoxy Hybrid Composites. SPE Polymers. 2026;7(2). doi:10.1002/pls2.70043

BibTeX
@article{Zahid2026,
  author = {Zahid, Ishrak Ibn and Nath, Titu and Sur, Nayan and Debnath, Arup Kumar and Hasib, Md. Abdul},
  title = {Effect of Metal Oxide Fillers on the Thermo‐Mechanical and Physical Properties of Kenaf–Carbon Fiber Epoxy Hybrid Composites},
  journal = {SPE Polymers},
  year = {2026},
  volume = {7},
  number = {2},
  doi = {10.1002/pls2.70043}
}
Kostenlos starten →