EUVIMEDEUVIMED entdecken
Crossref

Development of a High‐Strength Two‐Component Polyurethane Structural Adhesive for Extreme Cryogenic Environments

Jingjing Wang, Bingyang Wang, Zhongkai Yue, Yanhui Cao, Kaifeng Chen, Yu Liang, Congshu Huang, Peixin Niu, Liuhe Wei, Yuhan Li

Polymer Engineering & Science · 14.11.2026

DOI: 10.1002/pen.71001 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymer Engineering & Science, online erschienen am 14.11.2026. Verfasst von Jingjing Wang und 9 weiteren Autor:innen. Die Arbeit nennt 23 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Structural adhesives used in liquefied natural gas (LNG) containment systems must retain reliable load transfer under severe thermomechanical mismatch near the boiling point of methane (approximately −163°C). Here, a series of two‐component polyurethane (PU) structural adhesives was developed using a phenyl‐based diol/diamine chain‐extender combination, an MDI/PM‐200‐based isocyanate‐terminated prepolymer, and silica microparticles. The best‐performing formulation within the investigated composition range, PU‐C5‐50, achieved lap‐shear strengths of 11.6 MPa at room temperature and 13.02 MPa at −163°C on sandblasted steel, corresponding to increases of 41.3% and 44.0%, respectively, relative to the unfilled PU‐C5‐0 formulation. Composition–property analysis showed that increasing PM‐200 incorporation was accompanied by an increased fraction of hydrogen‐bonded carbonyl species and enhanced hard‐segment association, while silica addition increased joint strength and promoted a transition from predominantly interfacial to cohesive failure. Contact‐angle measurements indicated favorable wetting of PU‐C5‐50 on sandblasted steel. Together with the observed failure‐mode evolution, the interfacial bonding is proposed to involve intimate adhesive–substrate contact, mechanical interlocking on the sandblasted surface, polar intermolecular interactions, and effective cohesive stress transfer. DMA, DSC, SEM, and SAXS indicated a highly crosslinked, predominantly amorphous and structurally isotropic material with disordered local hard‐segment aggregation rather than long‐range ordered microphase separation. These results demonstrate a practical route to combining high cohesive strength, interfacial compatibility, and short‐term cryogenic lap‐shear performance in two‐component PU adhesives for LNG‐related structural bonding.

Zitieren

APA

Wang, J., Wang, B., Yue, Z., Cao, Y., Chen, K., Liang, Y., Huang, C., Niu, P., Wei, L., & Li, Y. (2026). Development of a High‐Strength Two‐Component Polyurethane Structural Adhesive for Extreme Cryogenic Environments. Polymer Engineering & Science. https://doi.org/10.1002/pen.71001

Vancouver

Wang J, Wang B, Yue Z, Cao Y, Chen K, Liang Y, et al. Development of a High‐Strength Two‐Component Polyurethane Structural Adhesive for Extreme Cryogenic Environments. Polymer Engineering & Science. 2026. doi:10.1002/pen.71001

BibTeX
@article{Wang2026,
  author = {Wang, Jingjing and Wang, Bingyang and Yue, Zhongkai and Cao, Yanhui and Chen, Kaifeng and Liang, Yu and Huang, Congshu and Niu, Peixin and Wei, Liuhe and Li, Yuhan},
  title = {Development of a High‐Strength Two‐Component Polyurethane Structural Adhesive for Extreme Cryogenic Environments},
  journal = {Polymer Engineering & Science},
  year = {2026},
  doi = {10.1002/pen.71001}
}
Kostenlos starten →