EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Poly‐Ether‐Ether‐Ketone Melt Behavior in Fused Deposit Modeling Printing Moves

Paul Sager, Dan Komorr, Jan‐Malte Dellmuth, Ahmad Zeinolebadi, Rainer Adelung

Polymer Engineering & Science · 2026-08 · 66 (8) · 5998-6008

DOI: 10.1002/pen.70637 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymer Engineering & Science, online erschienen am 08.06.2026. Verfasst von Paul Sager und 4 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 19 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Polyetheretherketone (PEEK) offers superior mechanical and thermal properties for use in non‐assembly mechanisms manufactured by fused deposition modeling (FDM). However, the required precise control of the shear and cooling behavior during printing is still not sufficiently explored, which is limiting tolerance, accuracy, and functionality. This work investigates the shear viscosity and transient heat transfer of PEEK melt in FDM using rheological measurements, polarized light microscopy (PLM), differential scanning calorimetry (DSC), and a one‐dimensional numerical simulation including power‐law viscosity and heat conduction. Experiments show a thin solidified layer (~47–54 μm) at the print bed interface that solidifies rapidly without significant shear, leading to higher effective shear rates in the remaining melt and thus a larger orientation gradient across the strand height. PLM investigations indicate increasing birefringence at shear rates up to ~350 s −1 , consistent with growing molecular orientation, though contributions from crystalline morphology cannot be fully excluded. Surface instabilities follow at critical shear rates of approximately 750–810 s −1 . The simulation results align with the obtained solidified layer thickness and the shear profiles obtained by the experiments. A corrected shear rate equation is proposed to correct the effect of the unsheared, solidified layer. The findings presented in this work enhance the understanding of melt kinematics in FDM‐PEEK printing and provide a basis for informed parameter selection in the fabrication of non‐assembly mechanisms, contributing to improved tolerance control and reduced risk of surface defects.

Zitieren

APA

Sager, P., Komorr, D., Dellmuth, J., Zeinolebadi, A., & Adelung, R. (2026). Poly‐Ether‐Ether‐Ketone Melt Behavior in Fused Deposit Modeling Printing Moves. Polymer Engineering & Science, 66(8), 5998-6008. https://doi.org/10.1002/pen.70637

Vancouver

Sager P, Komorr D, Dellmuth J, Zeinolebadi A, Adelung R. Poly‐Ether‐Ether‐Ketone Melt Behavior in Fused Deposit Modeling Printing Moves. Polymer Engineering & Science. 2026;66(8):5998-6008. doi:10.1002/pen.70637

BibTeX
@article{Sager2026,
  author = {Sager, Paul and Komorr, Dan and Dellmuth, Jan‐Malte and Zeinolebadi, Ahmad and Adelung, Rainer},
  title = {Poly‐Ether‐Ether‐Ketone Melt Behavior in Fused Deposit Modeling Printing Moves},
  journal = {Polymer Engineering & Science},
  year = {2026},
  volume = {66},
  number = {8},
  pages = {5998--6008},
  doi = {10.1002/pen.70637}
}
Kostenlos starten →