PVDF ‐ HFP / PI ‐ SiO 2 composite sandwich separators for lithium‐ion batteries: Fabrication and post‐processing
Polymer Engineering & Science · 2025-02 · 65 (2) · 478-491
DOI: 10.1002/pen.27016 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymer Engineering & Science, online erschienen am 31.12.2024. Verfasst von Solmaz Parsaei und 2 weiteren Autor:innen. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 44 Literaturangaben.
Abstract (Originalsprache)
PVDF‐HFP/PI‐SiO 2 three‐layer sandwich separators of lithium‐ion battery were fabricated by electrospinning and post‐processing. PI‐SiO 2 composite side layers were electrospun with 5, 10, and 15 wt% SiO 2 , while PVDF‐HFP was used as the middle layer. Then, mechanical/thermal post‐processing was applied on electrospun sandwich separators. Results showed that the addition of SiO 2 reduced fibers diameter, increased wettability, and improved mechanical strength of the PVDF‐HFP/PI separator. The separator with 10% SiO 2 has shown the highest tensile strength (21.1 MPa) and puncture strength (1.573 KgF). Differential scanning calorimetric, thermo‐gravimetric analysis, thermal shrinkage, and flammability results showed that PI‐SiO 2 /PVDF‐HFP/PI‐SiO 2 separators had excellent thermal stability with respect to PP separator, while these properties were improved with SiO 2 content. The fabricated sandwich separators had high air permeability and volumetric porosity of more than 63%. The discharge capacity of PI‐SiO 2 /PVDF‐HFP/PI‐SiO 2 was enhanced at high current densities, as it was improved from 117 to 125 mAh/mg at the discharge rate of 2C, by increasing the percentage of SiO 2 from 0 to 15 (wt%). Highlights Tensile strength was improved more than 500% by applying post‐processing. SiO 2 reduced fibers diameter, and improved wettability and mechanical strength. Capacity was improved from 117 to 125 mAh/mg at the rate of 2C with SiO 2 . Fabricated separators had ignition resistance compared to commercial separators.
Zitieren
APA
Parsaei, S., Zebarjad, S. M., & Moghim, M. H. (2025). PVDF ‐ HFP / PI ‐ SiO 2 composite sandwich separators for lithium‐ion batteries: Fabrication and post‐processing. Polymer Engineering & Science, 65(2), 478-491. https://doi.org/10.1002/pen.27016
Vancouver
Parsaei S, Zebarjad SM, Moghim MH. PVDF ‐ HFP / PI ‐ SiO 2 composite sandwich separators for lithium‐ion batteries: Fabrication and post‐processing. Polymer Engineering & Science. 2025;65(2):478-491. doi:10.1002/pen.27016
BibTeX
@article{Parsaei2025,
author = {Parsaei, Solmaz and Zebarjad, Seyed Mojtaba and Moghim, Mohammad Hadi},
title = {PVDF ‐ HFP / PI ‐ SiO 2 composite sandwich separators for lithium‐ion batteries: Fabrication and post‐processing},
journal = {Polymer Engineering & Science},
year = {2025},
volume = {65},
number = {2},
pages = {478--491},
doi = {10.1002/pen.27016}
}
EUVIMED