EUVIMEDEUVIMED entdecken
Crossref

Effect of Low Temperatures and Drilled Hole Diameters on Flexural Properties and Failure Mechanisms of 3D Angle‐Interlock Woven Drilled Hole Composites

Yi Ren, Xiaonan Wang, Ying Chai, Yiwei Ouyang, Yiran Han, Xin Sun, Xiaoke Huang, Duyan Zhang, Yang Liu, Xiaozhou Gong

Polymer Composites · 18.11.2026

DOI: 10.1002/pc.71895 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymer Composites, online erschienen am 18.11.2026. Verfasst von Yi Ren und 9 weiteren Autor:innen. Die Arbeit nennt 36 Literaturangaben. Gefördert von: Hubei Provincial Department of Education.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study systematically investigates the flexural behavior of three‐dimensional angle‐interlock woven drilled‐hole composites (3DAWDHC) under low‐temperature conditions. Three 3DAWDHC architectures, namely through‐angle interlocking (TI), shallow‐cross bending (SB), and shallow‐cross straight (SS), were fabricated and subjected to three‐point bending tests over a temperature range of −60°C to 20°C and drilled hole diameters of 0–6 mm. The effects of temperature and hole diameter on peak load, flexural strength, and flexural modulus were quantitatively evaluated. The results demonstrate that both temperature and hole diameter significantly regulate the flexural properties of 3DAWDHC in opposite manners. Taking the TI structure as a representative, flexural strength and flexural modulus increase by 14.6% and 44.0%, respectively, when temperature decreases from 20°C to −60°C, relative to the room‐temperature non‐drilled baseline. By contrast, when the drilled hole diameter increases from 0 to 6 mm at 20°C, flexural strength and flexural modulus decrease by 22.8% and 28.9%, respectively. Regarding failure characteristics, lower temperatures aggravate matrix embrittlement and induce more severe brittle fracture, while larger drilled holes reduce the macroscopic failure area but deepen crack propagation along the thickness direction. These findings provide fundamental data and design guidance for 3D woven joint structures serving in cryogenic aerospace environments.

Förderung

  • Hubei Provincial Department of Education

Zitieren

APA

Ren, Y., Wang, X., Chai, Y., Ouyang, Y., Han, Y., Sun, X., Huang, X., Zhang, D., Liu, Y., & Gong, X. (2026). Effect of Low Temperatures and Drilled Hole Diameters on Flexural Properties and Failure Mechanisms of 3D Angle‐Interlock Woven Drilled Hole Composites. Polymer Composites. https://doi.org/10.1002/pc.71895

Vancouver

Ren Y, Wang X, Chai Y, Ouyang Y, Han Y, Sun X, et al. Effect of Low Temperatures and Drilled Hole Diameters on Flexural Properties and Failure Mechanisms of 3D Angle‐Interlock Woven Drilled Hole Composites. Polymer Composites. 2026. doi:10.1002/pc.71895

BibTeX
@article{Ren2026,
  author = {Ren, Yi and Wang, Xiaonan and Chai, Ying and Ouyang, Yiwei and Han, Yiran and Sun, Xin and Huang, Xiaoke and Zhang, Duyan and Liu, Yang and Gong, Xiaozhou},
  title = {Effect of Low Temperatures and Drilled Hole Diameters on Flexural Properties and Failure Mechanisms of 3D Angle‐Interlock Woven Drilled Hole Composites},
  journal = {Polymer Composites},
  year = {2026},
  doi = {10.1002/pc.71895}
}
Kostenlos starten →