EUVIMEDEUVIMED entdecken
Crossref

Tribological Behavior of Self‐Lubricating PEEK /Graphite/ Ti 3 SiC 2 Composites Under Dry Sliding Friction

Yang Zhang, Qingsong Li, Xi Xie, Guoxin Sui

Polymers for Advanced Technologies · 2025-02 · 36 (2)

DOI: 10.1002/pat.70128 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers for Advanced Technologies, online erschienen am 23.02.2025. Verfasst von Yang Zhang und 3 weiteren Autor:innen. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 31 Literaturangaben. Gefördert von: National Natural Science Foundation of China.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Most polymers and composites suffer from high friction and wear due to their inherent lack of self‐lubrication under dry sliding friction. Herein, the lamellar Ti 3 SiC 2 MAX material is prepared via vacuum sintering of a powder mixture containing Ti, Si, and TiC in the molar ratio of 1:1.1:1.8 at 1500°C under a pressure of 30 MPa for 2 h. Combined with a soft graphite phase (5 wt%), self‐lubricating PEEK/Graphite/Ti 3 SiC 2 (PG‐T) composites are successfully prepared, dependent on Ti 3 SiC 2 (5 and 15 wt%) as a hard reinforced phase and lubrication additive. PG‐T composites are fabricated via a multistep compounding approach using a twin‐screw extruder. The incorporation of Ti 3 SiC 2 and graphite within the PEEK matrix manifests a highly pronounced synergistic effect, which not only facilitates effective lubrication but also significantly enhances the load‐bearing capability, thereby effectively circumventing direct contact between the counterface and the polymeric matrix. The sliding tests are conducted on the pins (diameter: 6.0 mm, height: 17.0 mm) and friction pair (45#steel, roughness Ra: 148 nm) under dry friction. In terms of PV‐condition (up to 6 MPa and 3 m/s) (PV is a parameter that reflects the load‐bearing capacity of polymer materials, which is defined by multi‐plying the pressure P by the sliding speed V), PG5‐T15 exhibits self‐lubricating properties, featured by an average coefficient of friction (ACOF) as low as 0.119 for the pin‐plate test and a specific wear rate (SWR) of only 0.58 × 10 −6 mm 3 /Nm. Meanwhile, PG‐T composites present excellent thermal properties based on the thermal expansion coefficients (CTEs) and storage moduli (G′) during friction and wear. Considering the practical applications of tribo‐composites, these findings highlight the potential of PG‐T composite as a candidate for demanding tribological applications.

Förderung

  • National Natural Science Foundation of China

Zitieren

APA

Zhang, Y., Li, Q., Xie, X., & Sui, G. (2025). Tribological Behavior of Self‐Lubricating PEEK /Graphite/ Ti 3 SiC 2 Composites Under Dry Sliding Friction. Polymers for Advanced Technologies, 36(2). https://doi.org/10.1002/pat.70128

Vancouver

Zhang Y, Li Q, Xie X, Sui G. Tribological Behavior of Self‐Lubricating PEEK /Graphite/ Ti 3 SiC 2 Composites Under Dry Sliding Friction. Polymers for Advanced Technologies. 2025;36(2). doi:10.1002/pat.70128

BibTeX
@article{Zhang2025,
  author = {Zhang, Yang and Li, Qingsong and Xie, Xi and Sui, Guoxin},
  title = {Tribological Behavior of Self‐Lubricating PEEK /Graphite/ Ti 3 SiC 2 Composites Under Dry Sliding Friction},
  journal = {Polymers for Advanced Technologies},
  year = {2025},
  volume = {36},
  number = {2},
  doi = {10.1002/pat.70128}
}
Kostenlos starten →