EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development of a drone‐borne electromagnetic survey system for searching for buried vehicles and soil resistivity mapping

Yuji Mitsuhata, Takumi Ueda, Akiya Kamimura, Shin Kato, Atsushi Takeuchi, Chikara Aduma, Toshiyuki Yokota

Near Surface Geophysics · 2022-02 · 20 (1) · 16-29

DOI: 10.1002/nsg.12189 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Near Surface Geophysics, online erschienen am 27.12.2021. Verfasst von Yuji Mitsuhata und 6 weiteren Autor:innen. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

We developed a drone‐borne electromagnetic survey system using a commercial multi‐frequency electromagnetic sensor equipped with a GPS receiver, a WiFi serial transceiver, and an ultrasonic distance sensor to measure the height of the electromagnetic sensor above the ground surface. The electromagnetic sensor was suspended from a drone with ropes. The distance between the drone and the electromagnetic sensor was adjusted to minimize the influence of electromagnetic noise generated by the drone, and to stabilize the electromagnetic sensor during flight. The system was tested at two experimental sites. The first site consisted of two buried vehicles to simulate a landslide. We assumed a scenario in which the search for the buried vehicles was urgent and accessibility to the area was limited. The second site consisted of wet and dry agricultural fields to test resistivity mapping. In the first test, we used the in‐phase component of the measured data to locate the vehicles. The shallower vehicle was identified clearly, while the deeper vehicle was located successfully, albeit less easily. In the second test, the quadrature component was used for one‐dimensional inversion after data processing, which included data smoothing, resampling and bias noise correction. The bias noise was measured while hovering the drone at a high altitude to negate the influence of ground conductivity. The results showed that the resistivity distributions could be mapped at some depths by using a five‐frequency‐processed quadrature component, and clearly showed the difference between the wet and dry fields. The crucial parameter in the evaluations of these targets was the height of the electromagnetic sensor above the ground surface, which was measured continuously during flight. The results demonstrated the potential of the survey system to search for buried metal objects and for shallow subsurface resistivity mapping over relatively large areas.

Zitieren

APA

Mitsuhata, Y., Ueda, T., Kamimura, A., Kato, S., Takeuchi, A., Aduma, C., & Yokota, T. (2022). Development of a drone‐borne electromagnetic survey system for searching for buried vehicles and soil resistivity mapping. Near Surface Geophysics, 20(1), 16-29. https://doi.org/10.1002/nsg.12189

Vancouver

Mitsuhata Y, Ueda T, Kamimura A, Kato S, Takeuchi A, Aduma C, et al. Development of a drone‐borne electromagnetic survey system for searching for buried vehicles and soil resistivity mapping. Near Surface Geophysics. 2022;20(1):16-29. doi:10.1002/nsg.12189

BibTeX
@article{Mitsuhata2022,
  author = {Mitsuhata, Yuji and Ueda, Takumi and Kamimura, Akiya and Kato, Shin and Takeuchi, Atsushi and Aduma, Chikara and Yokota, Toshiyuki},
  title = {Development of a drone‐borne electromagnetic survey system for searching for buried vehicles and soil resistivity mapping},
  journal = {Near Surface Geophysics},
  year = {2022},
  volume = {20},
  number = {1},
  pages = {16--29},
  doi = {10.1002/nsg.12189}
}
Kostenlos starten →