EUVIMEDEUVIMED entdecken
Fallbericht

3D Printing of a Patient‐Specific Biomodel and Cutting Guide for Metatarsal Reconstruction With an Osteocutaneous SCIP Flap Using Open‐Source Software: A Case Report

Miguel L Obaíd iD, Antonio Núñez, Leonardo Parada, Vanessa Oñate, Cristina Almeida, Ricardo Roa, Nicolás Pereira

Microsurgery · 2026-05 · 46 (4)

DOI: 10.1002/micr.70236 ↗

Kurz gefasst

Fallbericht in der Zeitschrift Microsurgery, online erschienen am 05.05.2026. Verfasst von Miguel L Obaíd und 6 weiteren Autor:innen. Beteiligte Einrichtung: Plastic Surgery Department, Hospital del Salvador, Santiago, Chile. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Plastic Surgery Procedures, Metatarsal Bones, Perforator Flap. Die Arbeit nennt 15 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Technology‐assisted planning is increasingly integrated into reconstructive plastic surgery, including virtual reality, augmented reality, and three‐dimensional (3D) printing. 3D printing has been especially useful in maxillofacial surgery, both for patient‐specific cutting guides for osteotomies and for biomodels to customize osteosynthesis plates. However, to our knowledge, there have been no reports of a 3D‐printed cutting guide to harvest a custom iliac crest bone flap based on the deep branch of the superficial circumflex iliac artery perforator (SCIP) flap, together with a biomodel of the foot skeleton with the bone defect for intraoperative use. We report a 36‐year‐old man with a 45‐mm bone defect of the first metatarsal and a 9 × 8 cm skin defect on the dorsum of the right foot after firearm trauma. Computer‐aided design and computer‐aided manufacturing (CAD/CAM) using open‐source software were used to prepare a cutting guide that allowed harvesting a bone flap of precise dimensions and a biomodel that enabled intraoperative adjustment of the flap without pedicle division. Reconstruction was achieved with a 45‐mm bone flap based on the deep branch of the SCIP and a 9 × 8 cm skin flap based on the superficial branch of the SCIP. Both flaps survived without complications; bone consolidation was observed at 4 months, and at 10 months, the patient had an adequate, pain‐free gait. This case illustrates that an open‐source, low‐cost 3D‐printing workflow may be a useful adjunct for planning and execution of metatarsal reconstruction with osteocutaneous free flaps.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalPlastic Surgery ProceduresMetatarsal BonesPerforator FlapFoot InjuriesWounds, GunshotHumansMaleAdultComputer-Aided DesignSoftwareBone Transplantation

Autor:innen und Institutionen

  • Plastic Surgery Department, Hospital del Salvador, Santiago, Chile.
  • Maxillofacial Department, Universidad Mayor, Santiago, Chile.
  • Plastic Surgery and Burns Department, Hospital del Trabajador, Santiago, Chile.
  • Clínica Nea, Santiago, Chile.
  • Plastic Surgery Department, Hospital Luis Vernaza, Guayaquil, Ecuador.

ORCID-Profile: Miguel L Obaíd

Zitieren

APA

Obaíd, M. L., Núñez, A., Parada, L., Oñate, V., Almeida, C., Roa, R., & Pereira, N. (2026). 3D Printing of a Patient‐Specific Biomodel and Cutting Guide for Metatarsal Reconstruction With an Osteocutaneous SCIP Flap Using Open‐Source Software: A Case Report. Microsurgery, 46(4). https://doi.org/10.1002/micr.70236

Vancouver

Obaíd ML, Núñez A, Parada L, Oñate V, Almeida C, Roa R, et al. 3D Printing of a Patient‐Specific Biomodel and Cutting Guide for Metatarsal Reconstruction With an Osteocutaneous SCIP Flap Using Open‐Source Software: A Case Report. Microsurgery. 2026;46(4). doi:10.1002/micr.70236

BibTeX
@article{Obad2026,
  author = {Obaíd, Miguel L and Núñez, Antonio and Parada, Leonardo and Oñate, Vanessa and Almeida, Cristina and Roa, Ricardo and Pereira, Nicolás},
  title = {3D Printing of a Patient‐Specific Biomodel and Cutting Guide for Metatarsal Reconstruction With an Osteocutaneous SCIP Flap Using Open‐Source Software: A Case Report},
  journal = {Microsurgery},
  year = {2026},
  volume = {46},
  number = {4},
  doi = {10.1002/micr.70236}
}
Kostenlos starten →