EUVIMEDEUVIMED entdecken
Crossref

Tuning the Mechanical Properties of 3D‐printed Objects by Mixing Chain Transfer Agents in Radical Promoted Cationic RAFT Polymerization

Guangliang Li, Bowen Zhao, Yuzhen Zhu, Shiliang He, Jiajia Li, Jian Zhu iD, Na Li

Macromolecular Rapid Communications · 2024-11 · 45 (22)

DOI: 10.1002/marc.202400515 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Macromolecular Rapid Communications, online erschienen am 09.08.2024. Verfasst von Guangliang Li und 6 weiteren Autor:innen. Beteiligte Einrichtung: State and Local Joint Engineering Laboratory for Novel Functional Polymeric Materials, Jiangsu Key Laboratory of Advanced Functional Polymer Design a…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Polymerization, Cations. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 41 Literaturangaben. Gefördert von: Suzhou Cutting-edge Technology Research Project, National Natural Science Foundation of China, Jiangsu Higher Education Institutions.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The utilization of (cationic) reversible addition‐fragmentation chain transfer (RAFT) polymerization in photoinduced three‐dimensional (3D) printing has emerged as a robust technique for fabricating a variety of stimuli‐responsive materials. However, methods for precisely adjusting the mechanical properties of these materials remain limited, thereby constraining their broader applicability. In this study, a facile way is introduced to modulate the mechanical properties of 3D printed objects by mixing two chain transfer agents (CTAs) within a radical‐promoted cationic RAFT (RPC‐RAFT) polymerization‐based 3D printing process. Through systematic investigations employing tensile testing and dynamic mechanical analysis (DMA), the influence of CTA concentration and molar ratio between two CTAs on the mechanical behavior of the printed objects are explored. These findings demonstrate that higher concentrations of CTAs or a greater molar ratio of the more active CTA within the mixed CTAs result in decreased Young's modulus and glass transition temperatures of the printed objects. Moreover, the tensile failure strain increased with the increasing CTA content, i.e., the samples became more ductile. This methodology broadens the toolbox available for tailoring the mechanical properties of 3D printed materials.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalPolymerizationCationsPolymersTensile Strength

Stichwörter der Autor:innen

3D printingcationic RAFT polymerizationmechanical propertiespolymer dispersity

Substanzen

CationsPolymers

Autor:innen und Institutionen

  • State and Local Joint Engineering Laboratory for Novel Functional Polymeric Materials, Jiangsu Key Laboratory of Advanced Functional Polymer Design and Application, Suzhou key Laboratory of Macromolecular Design and Pre…

ORCID-Profile: Jian Zhu

Förderung

  • Suzhou Cutting-edge Technology Research Project
  • National Natural Science Foundation of China
  • Jiangsu Higher Education Institutions
  • Soochow University

Zitieren

APA

Li, G., Zhao, B., Zhu, Y., He, S., Li, J., Zhu, J., & Li, N. (2024). Tuning the Mechanical Properties of 3D‐printed Objects by Mixing Chain Transfer Agents in Radical Promoted Cationic RAFT Polymerization. Macromolecular Rapid Communications, 45(22). https://doi.org/10.1002/marc.202400515

Vancouver

Li G, Zhao B, Zhu Y, He S, Li J, Zhu J, et al. Tuning the Mechanical Properties of 3D‐printed Objects by Mixing Chain Transfer Agents in Radical Promoted Cationic RAFT Polymerization. Macromolecular Rapid Communications. 2024;45(22). doi:10.1002/marc.202400515

BibTeX
@article{Li2024,
  author = {Li, Guangliang and Zhao, Bowen and Zhu, Yuzhen and He, Shiliang and Li, Jiajia and Zhu, Jian and Li, Na},
  title = {Tuning the Mechanical Properties of 3D‐printed Objects by Mixing Chain Transfer Agents in Radical Promoted Cationic RAFT Polymerization},
  journal = {Macromolecular Rapid Communications},
  year = {2024},
  volume = {45},
  number = {22},
  doi = {10.1002/marc.202400515}
}
Kostenlos starten →