EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Influence of Mixed Solvent in the Morphology and Hydrophobicity of Electrospun Polystyrene Porous Fibers

Guilherme Henrique França Melo iD, Uttandaraman Sundararaj iD

Macromolecular Rapid Communications · 2024

DOI: 10.1002/marc.202400403 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Macromolecular Rapid Communications, 2024. Verfasst von Guilherme Henrique França Melo und 1 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemical and Petroleum Engineering, University of Calgary, 2500 University Dr NW, Calgary, AB T2N 1N4, Canada. Hauptthemen laut MEDLINE: Polystyrenes, Hydrophobic and Hydrophilic Interactions, Solvents, Surface Properties. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Natural Sciences and Engineering Research Council of Canada.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Electrospun polystyrene (PS) fibers are produced using a mixed solvent of chloroform and n,n‐dimethylformamide (DMF) to investigate the influence of the solvent ratio on the fiber surface morphology and contact angle of the obtained mats. Electrospinning is a simple processing technique for producing fibers with diameters in the range of nanometers to a few micrometers. When using the different solvent ratios for this process, porous PS membranes are created due to nonsolvent and thermally induced phase separation (N‐TIPS). The morphology of the fibers is analyzed through scanning electron microscopy (SEM), which showed that fibers have diameters between 200 nm and 6 µm. SEM also revealed that the pores present on the surface of the fibers vary from densely compacted and well‐formed nanopores with diameters in the range of 20–50 nm to larger pores with sizes of ≈100–200 nm. The pore size varied with different solvent ratios. The surface area is analyzed using the Brunauer–Emmett–Teller (BET) method and found that the polymeric fibers have a high surface area (≈35 m 2 g −1 ). The fibers with such morphology are highly hydrophobic, with a contact angle higher than 143°. These materials are excellent candidates for applications in textiles, filtration, and biomedical fields.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolystyrenesHydrophobic and Hydrophilic InteractionsSolventsSurface PropertiesPorosityDimethylformamideParticle SizeMicroscopy, Electron, ScanningChloroform

Stichwörter der Autor:innen

DMFchloroformelectrospinninghydrophobicitypolystyreneporous fibersolvents

Substanzen

PolystyrenesSolventsDimethylformamideChloroform

Autor:innen und Institutionen

  • Department of Chemical and Petroleum Engineering, University of Calgary, 2500 University Dr NW, Calgary, AB T2N 1N4, Canada.

ORCID-Profile: Guilherme Henrique França Melo, Uttandaraman Sundararaj

Förderung

  • Natural Sciences and Engineering Research Council of Canada

Zitieren

APA

Melo, G. H. F., & Sundararaj, U. (2024). Influence of Mixed Solvent in the Morphology and Hydrophobicity of Electrospun Polystyrene Porous Fibers. Macromolecular Rapid Communications. https://doi.org/10.1002/marc.202400403

Vancouver

Melo GHF, Sundararaj U. Influence of Mixed Solvent in the Morphology and Hydrophobicity of Electrospun Polystyrene Porous Fibers. Macromolecular Rapid Communications. 2024. doi:10.1002/marc.202400403

BibTeX
@article{Melo2024,
  author = {Melo, Guilherme Henrique França and Sundararaj, Uttandaraman},
  title = {Influence of Mixed Solvent in the Morphology and Hydrophobicity of Electrospun Polystyrene Porous Fibers},
  journal = {Macromolecular Rapid Communications},
  year = {2024},
  doi = {10.1002/marc.202400403}
}
Kostenlos starten →