EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Fabrication of Soft Transparent Patient‐Specific Vascular Models with Stereolithographic 3D printing and Thiol‐Based Photopolymerizable Coatings

Elnaz Hosseinzadeh iD, Beatriz Bosques-Palomo, Francisco Carmona-Arriaga, Mario Alejandro Fabiani iD, Alan Aguirre-Soto iD

Macromolecular Rapid Communications · 2024-03 · 45 (6)

DOI: 10.1002/marc.202300611 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Macromolecular Rapid Communications, online erschienen am 08.01.2024. Verfasst von Elnaz Hosseinzadeh und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Engineering and Sciences, Tecnologico de Monterrey, Nuevo León, Monterrey, 64849, México. Hauptthemen laut MEDLINE: Sulfhydryl Compounds, Polyethylene Glycols. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 109 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Consejo Nacional de Ciencia y Tecnología.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

An ideal vascular phantom should be anatomically accurate, have mechanical properties as close as possible to the tissue, and be sufficiently transparent for ease of visualization. However, materials that enable the convergence of these characteristics have remained elusive. The fabrication of patient‐specific vascular phantoms with high anatomical fidelity, optical transparency, and mechanical properties close to those of vascular tissue is reported. These final properties are achieved by 3D printing patient‐specific vascular models with commercial elastomeric acrylic‐based resins before coating them with thiol‐based photopolymerizable resins. Ternary thiol‐ene‐acrylate chemistry is found optimal. A PETMP/allyl glycerol ether (AGE)/polyethylene glycol diacrylate (PEGDA) coating with a 30/70% AGE/PEGDA ratio applied on a flexible resin yielded elastic modulus, UTS, and elongation of 3.41 MPa, 1.76 MPa, and 63.2%, respectively, in range with the human aortic wall. The PETMP/AGE/PEGDA coating doubled the optical transmission from 40% to 80%, approaching 88% of the benchmark silicone‐based elastomer. Higher transparency correlates with a decrease in surface roughness from 2000 to 90 nm after coating. Coated 3D‐printed anatomical replicas are showcased for pre‐procedural planning and medical training with good radio‐opacity and echogenicity. Thiol‐click chemistry coatings, as a surface treatment for elastomeric stereolithographic 3D‐printed objects, address inherent limitations of photopolymer‐based additive manufacturing.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Sulfhydryl CompoundsPolyethylene GlycolsHumansPrinting, Three-Dimensional

Stichwörter der Autor:innen

elastomersphotocurable coatingsstereolithographic 3D printingthiol‐click chemistryvascular phantoms

Substanzen

Sulfhydryl Compoundspoly(ethylene glycol)diacrylatePolyethylene Glycols

Autor:innen und Institutionen

  • School of Engineering and Sciences, Tecnologico de Monterrey, Nuevo León, Monterrey, 64849, México.
  • School of Medicine and Health Sciences, Tecnologico de Monterrey, Nuevo León, Monterrey, 64710, México.

ORCID-Profile: Elnaz Hosseinzadeh, Mario Alejandro Fabiani, Alan Aguirre-Soto

Förderung

  • Consejo Nacional de Ciencia y Tecnología

Zitieren

APA

Hosseinzadeh, E., Bosques-Palomo, B., Carmona-Arriaga, F., Fabiani, M. A., & Aguirre-Soto, A. (2024). Fabrication of Soft Transparent Patient‐Specific Vascular Models with Stereolithographic 3D printing and Thiol‐Based Photopolymerizable Coatings. Macromolecular Rapid Communications, 45(6). https://doi.org/10.1002/marc.202300611

Vancouver

Hosseinzadeh E, Bosques-Palomo B, Carmona-Arriaga F, Fabiani MA, Aguirre-Soto A. Fabrication of Soft Transparent Patient‐Specific Vascular Models with Stereolithographic 3D printing and Thiol‐Based Photopolymerizable Coatings. Macromolecular Rapid Communications. 2024;45(6). doi:10.1002/marc.202300611

BibTeX
@article{Hosseinzadeh2024,
  author = {Hosseinzadeh, Elnaz and Bosques-Palomo, Beatriz and Carmona-Arriaga, Francisco and Fabiani, Mario Alejandro and Aguirre-Soto, Alan},
  title = {Fabrication of Soft Transparent Patient‐Specific Vascular Models with Stereolithographic 3D printing and Thiol‐Based Photopolymerizable Coatings},
  journal = {Macromolecular Rapid Communications},
  year = {2024},
  volume = {45},
  number = {6},
  doi = {10.1002/marc.202300611}
}
Kostenlos starten →