EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Cooling Rate on Physical Foaming Behavior of Molten Isotactic Polypropylene Systems

Rajesh Kumar Sharma, Kenta Ushida, Mirei Ino, Hideo Akimoto, Hisahiro Tanaka, Masato Goto, Takeshi Sato, Kenji Yoshimoto, Kentaro Taki

Macromolecular Materials and Engineering · 2026-07 · 311 (7)

DOI: 10.1002/mame.70261 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Macromolecular Materials and Engineering, online erschienen am 13.07.2026. Verfasst von Rajesh Kumar Sharma und 8 weiteren Autor:innen. Die Arbeit nennt 46 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Physical foaming of polymers is widely used to produce lightweight materials with improved thermal and mechanical properties. This study investigated the effect of cooling rate on the foaming behavior of two isotactic polypropylene (iPP) systems–a linear homopolymer (H1) and a long‐chain branched homopolymer (Homo‐LCB, L2). Polymer samples were saturated with nitrogen gas at 7 MPa and 200°C for 1 h, then cooled at controlled rates of 24, 40, and 52°C/min under constant pressure and depressurized at T d = 110°C–200°C to induce bubble nucleation. Bubble nucleation was monitored using high‐resolution visualization system and X‐ray computed tomography (X‐ray CT) imaging. The results showed that number of bubbles increased around T d ∼130°C, reached a maximum at 120°C for cooling rates of 40 and 52°C/min, and at 115°C for 24°C/min. Higher cooling rates resulted in the formation of more bubbles. Additionally, the L2 samples consistently exhibited higher bubble counts compared to H1. Differential scanning calorimetry (DSC), small‐angle X‐ray scattering (SAXS), and wide‐angle X‐ray diffraction (WAXD) analyses revealed that increased cooling rates led to a reduction in crystallinity. Upon cooling, increasing crystallinity initially enhanced bubble nucleation, then hindered it. These findings support polymer foam design for diverse applications.

Zitieren

APA

Sharma, R. K., Ushida, K., Ino, M., Akimoto, H., Tanaka, H., Goto, M., Sato, T., Yoshimoto, K., & Taki, K. (2026). Influence of Cooling Rate on Physical Foaming Behavior of Molten Isotactic Polypropylene Systems. Macromolecular Materials and Engineering, 311(7). https://doi.org/10.1002/mame.70261

Vancouver

Sharma RK, Ushida K, Ino M, Akimoto H, Tanaka H, Goto M, et al. Influence of Cooling Rate on Physical Foaming Behavior of Molten Isotactic Polypropylene Systems. Macromolecular Materials and Engineering. 2026;311(7). doi:10.1002/mame.70261

BibTeX
@article{Sharma2026,
  author = {Sharma, Rajesh Kumar and Ushida, Kenta and Ino, Mirei and Akimoto, Hideo and Tanaka, Hisahiro and Goto, Masato and Sato, Takeshi and Yoshimoto, Kenji and Taki, Kentaro},
  title = {Influence of Cooling Rate on Physical Foaming Behavior of Molten Isotactic Polypropylene Systems},
  journal = {Macromolecular Materials and Engineering},
  year = {2026},
  volume = {311},
  number = {7},
  doi = {10.1002/mame.70261}
}
Kostenlos starten →