Morphology and Mechanical Properties of Poly(vinyl alcohol)/Poly(lactic acid) Blend Films Prepared from Aqueous Dispersions
Macromolecular Materials and Engineering · 2024-01 · 309 (1)
DOI: 10.1002/mame.202300237 ↗Kurz gefasst
Fachartikel in der Zeitschrift Macromolecular Materials and Engineering, online erschienen am 15.10.2023. Verfasst von Giada Belletti und 8 weiteren Autor:innen. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Dipartimento di Scienze Chimiche e Farmaceutiche, Università degli Studi di Ferrara.
Abstract (Originalsprache)
In this study, the preparation of poly(vinyl alcohol) (PVA)/poly(lactic acid) (PLA) blends of different compositions, 100/0, 75/25, 50/50, 25/75, and 0/100, by mixing water solutions of the former and water dispersions of the latter polymer, is reported. Two distinct dispersions of PLA are prepared using a commercial‐grade polyester and two different surfactants, an anionic one and a neutral one. Films of PLA and of the corresponding blends are obtained by simply drying at 60 °C the water dispersions without or with the PVA. The films are characterized by infrared spectroscopy, differential scanning calorimetry (DSC), and scanning electron microscope (SEM) analysis. This evidences an island‐like morphology, with the continuous phase consisting of a PVA rich phase at all compositions except 25/75, for which an inverted phase composition, with a continuous phase made mostly of PLA, is instead found. Voids caused by air bubbles trapped in the initial mixture are observed in particular in the formulations with the anionic surfactant. The trapped bubbles result in premature thermal degradation by thermogravimetric analysis (TGA) and mechanical failure during clamping. Films with the neutral stabilizer are tougher than the bare commercial PLA, with Young modulus and elongation at break depending on the combination of the composition and arrangement of blend phases.
Förderung
- Dipartimento di Scienze Chimiche e Farmaceutiche, Università degli Studi di Ferrara
Zitieren
APA
Belletti, G., Ronconi, G., Mazzanti, V., Buratti, E., Marchi, L., Sotgiu, G., Calosi, M., Mollica, F., & Bertoldo, M. (2024). Morphology and Mechanical Properties of Poly(vinyl alcohol)/Poly(lactic acid) Blend Films Prepared from Aqueous Dispersions. Macromolecular Materials and Engineering, 309(1). https://doi.org/10.1002/mame.202300237
Vancouver
Belletti G, Ronconi G, Mazzanti V, Buratti E, Marchi L, Sotgiu G, et al. Morphology and Mechanical Properties of Poly(vinyl alcohol)/Poly(lactic acid) Blend Films Prepared from Aqueous Dispersions. Macromolecular Materials and Engineering. 2024;309(1). doi:10.1002/mame.202300237
BibTeX
@article{Belletti2024,
author = {Belletti, Giada and Ronconi, Giulia and Mazzanti, Valentina and Buratti, Elena and Marchi, Lorenzo and Sotgiu, Giovanna and Calosi, Matteo and Mollica, Francesco and Bertoldo, Monica},
title = {Morphology and Mechanical Properties of Poly(vinyl alcohol)/Poly(lactic acid) Blend Films Prepared from Aqueous Dispersions},
journal = {Macromolecular Materials and Engineering},
year = {2024},
volume = {309},
number = {1},
doi = {10.1002/mame.202300237}
}
EUVIMED