EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D‐printed custom ankle braces for people with Charcot‐Marie‐Tooth disease: A pilot study

Adam Philps, Mike Frecklington, Sarah Stewart iD

Journal of Foot and Ankle Research · 2024

DOI: 10.1002/jfa2.70013 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Foot and Ankle Research, 2024. Verfasst von Adam Philps und 2 weiteren Autor:innen. Beteiligte Einrichtung: Masterton Foot Clinic, Masterton, New Zealand. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Charcot-Marie-Tooth Disease, Braces. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

Charcot‐Marie‐Tooth disease (CMT) is a neurodegenerative condition resulting in footdrop, ankle instability and impaired balance and gait. This study aimed to determine (1) whether 3D‐printed custom ankle braces improve function and balance in people with CMT and (2) whether this is an acceptable device for use in this population.

Methods

A within‐subject comparison pragmatic/pilot study was undertaken. Ten people with CMT (mean [SD] age 48 [14] years, 60% male) were fitted with 3D‐printed ankle braces. Following a 4‐week wear‐in period, walking and balance tests and patient‐reported outcomes were assessed in two experimental conditions: (i) usual shoes and (ii) usual shoes with 3D‐printed custom ankle braces. Differences in outcome measures between experimental conditions were analysed using linear mixed models. Comfort, aesthetics and overall satisfaction of the brace were assessed via 100‐mm visual analogue scale (VAS). Adverse events and tripping/falls associated with the brace during the wear‐in period were also recorded by participants using daily diaries.

Results

A significant improvement was seen during single‐leg balance with eyes open ( p = 0.026, Cohen's d = 0.55) and a significant reduction in foot pain ( p = 0.045, Cohen's d = 0.82), with use of the ankle brace. Mean (SD) 100 mm VAS scores were 62.7 mm (17.9) for overall comfort and 73.9 mm (21.2) for overall satisfaction. Subjective data from the daily dairies showed that one participant found the brace too firm around the ankle due to loss of soft tissue mass and two participants found it challenging to don and doff the brace due to loss of hand dexterity.

Conclusion

This pilot study suggests that a 3D‐printed custom ankle brace may improve balance and reduce foot pain in people with CMT; however, larger‐scale trials are needed to further explore the impact of this brace on function and balance. Further customisation of the brace may also be required to improve acceptability for some people.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalCharcot-Marie-Tooth DiseaseBracesHumansPilot ProjectsMiddle AgedMaleFemaleAdultEquipment DesignPostural BalanceAnkle JointPatient SatisfactionShoesTreatment OutcomeWalkingPatient Reported Outcome Measures

Stichwörter der Autor:innen

Charcot‐Marie‐Tooth diseaseankle bracebalancefoot pain

Autor:innen und Institutionen

  • Masterton Foot Clinic, Masterton, New Zealand.
  • School of Clinical Sciences, Faculty of Health and Environmental Sciences, Auckland University of Technology, Auckland, New Zealand.

ORCID-Profile: Sarah Stewart

Zitieren

APA

Philps, A., Frecklington, M., & Stewart, S. (2024). 3D‐printed custom ankle braces for people with Charcot‐Marie‐Tooth disease: A pilot study. Journal of Foot and Ankle Research. https://doi.org/10.1002/jfa2.70013

Vancouver

Philps A, Frecklington M, Stewart S. 3D‐printed custom ankle braces for people with Charcot‐Marie‐Tooth disease: A pilot study. Journal of Foot and Ankle Research. 2024. doi:10.1002/jfa2.70013

BibTeX
@article{Philps2024,
  author = {Philps, Adam and Frecklington, Mike and Stewart, Sarah},
  title = {3D‐printed custom ankle braces for people with Charcot‐Marie‐Tooth disease: A pilot study},
  journal = {Journal of Foot and Ankle Research},
  year = {2024},
  doi = {10.1002/jfa2.70013}
}
Kostenlos starten →