EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

The effect of different liquids on the surface roughness and color stability of single shade and nanohybrid resin composites: An AFM and SEM analysis

İrem Ipek iD, Kübra Bilge iD

Microscopy Research and Technique · 2024-09 · 87 (9) · 2063-2071

DOI: 10.1002/jemt.24586 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Microscopy Research and Technique, online erschienen am 25.04.2024. Verfasst von İrem Ipek und 1 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Dentistry, Department of Pediatric Dentistry, Firat University, Elazig, Turkey. Hauptthemen laut MEDLINE: Surface Properties, Composite Resins, Microscopy, Atomic Force, Color. Die Arbeit wurde bisher 18-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The aim of this study is to evaluate the surface roughness (SR) and color changes of single‐shade and nanohybrid resin‐based restorative materials (RBC) after immersion in liquids at different pH values. For RBCs, a total of 120 specimens, 30 for each material, were prepared using 10 mm diameter and 2 mm thick molds. For flowable bulk fill RBC, a total of 40 specimens, 10 for each material, were prepared using 10 mm diameter and 4 mm thick molds ( n = 10). After initial color and SR measurements, samples were stored in the liquids for 14 days and all of the measurements were repeated on 14th days. Scanning electron microscopy and atomic force microscopy analyzes were performed in all groups. When SR results are examined; among all liquids, the highest SR value was observed in the Carisma Diamond One (CDO) group, while the lowest SR value was observed in the Omnichroma Flow Bulk (OMF) group ( p < .05). When the color changes (ΔE) results are examined; it was observed that CDO group had highest color change and OMF group had the lowest values. It has been observed that among the liquids, the liquids that affect the ΔE values of the materials the most are coffee and cola. When the ΔE values of the subgroups of the materials were examined, there was a statistically significant difference in all subgroups of RBCs ( p < .05). While acidic liquids increased the SR of RBCs, coffee more affected the color change of RBCs. Research Highlights Clinicians should keep in mind that the RBCs tested may change their surface properties and colors when exposed to various liquids. People who have RBCs should pay attention to the consumption of acidic and highly pigmented liquids.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Surface PropertiesComposite ResinsMicroscopy, Atomic ForceColorMicroscopy, Electron, ScanningHydrogen-Ion ConcentrationMaterials TestingCarbonated BeveragesCoffee

Stichwörter der Autor:innen

AFMSEMcolor stabilitysingle‐shade composite resinsurface roughness

Substanzen

Composite ResinsCoffee

Autor:innen und Institutionen

  • Faculty of Dentistry, Department of Pediatric Dentistry, Firat University, Elazig, Turkey.
  • Faculty of Dentistry, Department of Restorative Dentistry, Firat University, Elazig, Turkey.

ORCID-Profile: İrem Ipek, Kübra Bilge

Zitieren

APA

Ipek, İ., & Bilge, K. (2024). The effect of different liquids on the surface roughness and color stability of single shade and nanohybrid resin composites: An AFM and SEM analysis. Microscopy Research and Technique, 87(9), 2063-2071. https://doi.org/10.1002/jemt.24586

Vancouver

Ipek İ, Bilge K. The effect of different liquids on the surface roughness and color stability of single shade and nanohybrid resin composites: An AFM and SEM analysis. Microscopy Research and Technique. 2024;87(9):2063-2071. doi:10.1002/jemt.24586

BibTeX
@article{Ipek2024,
  author = {Ipek, İrem and Bilge, Kübra},
  title = {The effect of different liquids on the surface roughness and color stability of single shade and nanohybrid resin composites: An AFM and SEM analysis},
  journal = {Microscopy Research and Technique},
  year = {2024},
  volume = {87},
  number = {9},
  pages = {2063--2071},
  doi = {10.1002/jemt.24586}
}
Kostenlos starten →