Metallurgical characteristics of AA6061 aluminium and AZ31B magnesium dissimilar joints by fusion welding technique
Microscopy Research and Technique · 2024-06 · 87 (6) · 1210-1221
DOI: 10.1002/jemt.24510 ↗Kurz gefasst
Fachartikel in der Zeitschrift Microscopy Research and Technique, online erschienen am 02.02.2024. Verfasst von Addanki Ramaswamy und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, SASI Institute of Technology & Engineering, Tadepalligudem, India. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 39 Literaturangaben.
Abstract (Originalsprache)
Aluminium (Al) and magnesium (Mg) alloys are extensively used in the automobile sector because of their high strength‐to‐weight ratio, excellent castability low density and simplicity of recycling. Al‐Mg structures used in the automotive sector can potentially reduce their weight. Although there is a significant opportunity for substantial cost reduction, the use of magnesium in aluminium structures remains restricted. This study aims to weld 3 mm‐thick rolled sheets of AA6061 Al and AZ31B Mg alloy using the cold metal transfer (CMT) arc welding process. Three different filler wires (ER1100, ER4043, and ER5356) were used in the experiment. In this article, the mechanical and microstructure characteristics of Al/Mg dissimilar joints manufactured by CMT are evaluated and discussed in detail. Optical microscope (OM), scanning electron microscopy (SEM), energy dispersive x‐ray spectroscopy (EDX), and x‐ray diffraction (XRD) were used to analyze the CMT‐welded Al/Mg dissimilar joints. Of the three filler wires used, ER4043 (Al‐5%Si) filler wire yielded defect‐free sound joints due to the presence of Si, which improves the flow ability of molten filler during welding. The presence of Mg‐rich intermetallics‐Al 12 Mg 17) and Al‐rich intermetallics‐Al 3 Mg 2 were observed. The fractured area of the CMT‐welded Al/Mg dissimilar joints revealed the presence of the Mg‐rich intermetallics (Al 12 Mg 17 ), which is responsible for the decrease in tensile strength. The reduction of intermetallics, particularly of Mg‐rich intermetallics (Al 12 Mg 17 ) is important for improving joint strength. Research Highlights Cold metal transfer (CMT) arc welding was used to control the Al‐Mg‐rich intermetallics in the Al/Mg dissimilar joints. The microstructure, morphology and phase composition of the welded joints were studied by OM, SEM, TEM, EDS and XRD. The weld metal and AL substrate bonded with a strong interface, while weld metal and Mg substrate were joined at the epitaxial solidification area where the intermetallic compounds of Mg 2 Al 3 , Mg 17 Al 12 and Mg 2 Si are generated. The weld metal on the Mg side experienced brittle fracture, with a continuous distribution of Mg 2 Al 3 , Mg 17 Al 12 and Mg 2 Si.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, SASI Institute of Technology & Engineering, Tadepalligudem, India.
- Department of Mechanical Engineering, SRM University-AP, Mangalagiri, Andhra Pradesh, India.
- Department of Manufacturing Engineering, Annamalai University, Annamalainagar, India.
ORCID-Profile: Bellamkonda Prasanna Nagasai
Zitieren
APA
Ramaswamy, A., Nagasai, B. P., Dwivedy, M., Malarvizhi, S., & Balasubramanian, V. (2024). Metallurgical characteristics of AA6061 aluminium and AZ31B magnesium dissimilar joints by fusion welding technique. Microscopy Research and Technique, 87(6), 1210-1221. https://doi.org/10.1002/jemt.24510
Vancouver
Ramaswamy A, Nagasai BP, Dwivedy M, Malarvizhi S, Balasubramanian V. Metallurgical characteristics of AA6061 aluminium and AZ31B magnesium dissimilar joints by fusion welding technique. Microscopy Research and Technique. 2024;87(6):1210-1221. doi:10.1002/jemt.24510
BibTeX
@article{Ramaswamy2024,
author = {Ramaswamy, Addanki and Nagasai, Bellamkonda Prasanna and Dwivedy, Maheshwar and Malarvizhi, Sudersanan and Balasubramanian, Visvalingam},
title = {Metallurgical characteristics of AA6061 aluminium and AZ31B magnesium dissimilar joints by fusion welding technique},
journal = {Microscopy Research and Technique},
year = {2024},
volume = {87},
number = {6},
pages = {1210--1221},
doi = {10.1002/jemt.24510}
}
EUVIMED