EUVIMEDEUVIMED entdecken
Crossref

Using Digital 3D Models for Faculty Calibration and Measurement of Calibration Effectiveness: A Feasibility Study

Zaid Badr, Mohammad Tajik, Manal Hamdan, Brian D Hodgson

Journal of Dental Education · 17.08.2026

DOI: 10.1002/jdd.70347 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Dental Education, online erschienen am 17.08.2026. Verfasst von Zaid Badr und 3 weiteren Autor:innen. Beteiligte Einrichtung: Technological Innovation Center, Department of General Dental Sciences, School of Dentistry, Marquette University, Milwaukee, Wisconsin, USA. Die Arbeit nennt 12 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Purpose

Faculty calibration is necessary for consistent assessment of dental students, yet many calibration activities rely on attendance, discussions, or static images rather than objective evidence of evaluator agreement. This study evaluated the feasibility of using digital three‐dimensional (3D) tooth preparation models to support faculty calibration and measure calibration effectiveness.

Methods

This feasibility study was conducted using anonymized standard tessellation language files exported from student full‐coverage crown preparations in a preclinical fixed prosthodontics course. Ten representative cases were selected from approximately 200 preparations by two experienced faculty members to reflect a range of performance levels and common preparation errors. Fifteen faculty members participated in a 1‐h calibration session that included rubric review, instruction on evaluation criteria, and orientation to the 3D viewing software. Faculty then independently evaluated each case across eight preparation criteria. Inter‐rater reliability was analyzed using the intraclass correlation coefficient (ICC).

Results

The mean completion time was 51.3 min. The average‐measures ICC was 0.841, indicating good inter‐rater agreement among faculty evaluators. Faculty feedback and implementation observations suggested that the digital 3D model environment, which allowed rotation, magnification, sectioning, and measurement, supported the visualization of preparation features that could be difficult to evaluate using two‐dimensional images alone.

Conclusion

Digital 3D models provided a feasible method for faculty calibration and enabled objective measurement of calibration effectiveness. This approach may help dental schools move beyond attendance‐based calibration toward evidence‐based evaluation of faculty agreement, although additional studies are needed across institutions, procedures, and larger faculty samples.

Schlagwörter

Stichwörter der Autor:innen

3D modelsdental educationdigital dentistryfaculty calibrationpreclinical crow preparation assessmentpreclinical fixed prosthodontics assessment

Autor:innen und Institutionen

  • Technological Innovation Center, Department of General Dental Sciences, School of Dentistry, Marquette University, Milwaukee, Wisconsin, USA.
  • Department of General Practice, School of Dentistry, Virginia Commonwealth University, Richmond, Virginia, USA.
  • Department of Surgical and Diagnostic Sciences, School of Dentistry, Marquette University, Milwaukee, Wisconsin, USA.
  • Department of Oral and Craniofacial Sciences, School of Dentistry, Oregon Health and Science University, Portland, Oregon, USA.
  • Department of General Dental Sciences, School of Dentistry, Marquette University, Milwaukee, Wisconsin, USA.
  • Children's Wisconsin, Milwaukee, Wisconsin, USA.

Zitieren

APA

Badr, Z., Tajik, M., Hamdan, M., & Hodgson, B. D. (2026). Using Digital 3D Models for Faculty Calibration and Measurement of Calibration Effectiveness: A Feasibility Study. Journal of Dental Education. https://doi.org/10.1002/jdd.70347

Vancouver

Badr Z, Tajik M, Hamdan M, Hodgson BD. Using Digital 3D Models for Faculty Calibration and Measurement of Calibration Effectiveness: A Feasibility Study. Journal of Dental Education. 2026. doi:10.1002/jdd.70347

BibTeX
@article{Badr2026,
  author = {Badr, Zaid and Tajik, Mohammad and Hamdan, Manal and Hodgson, Brian D},
  title = {Using Digital 3D Models for Faculty Calibration and Measurement of Calibration Effectiveness: A Feasibility Study},
  journal = {Journal of Dental Education},
  year = {2026},
  doi = {10.1002/jdd.70347}
}
Kostenlos starten →