EUVIMEDEUVIMED entdecken
Crossref

Tissue Engineering 3D‐Printed Scaffold Using Allograft/Alginate/Gelatin Hydrogels Coated With Platelet‐Rich Fibrin or Adipose Stromal Vascular Fraction Induces Osteogenesis In Vitro

Sahar Baniameri iD, Hossein Aminianfar, Niusha Gharehdaghi, Amir-Ali Yousefi-Koma, Sadra Mohaghegh, Hanieh Nokhbatolfoghahaei, Arash Khojasteh

Journal of Cellular Physiology · 2025

DOI: 10.1002/jcp.31497 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Cellular Physiology, 2025. Verfasst von Sahar Baniameri und 6 weiteren Autor:innen. Beteiligte Einrichtung: Dental Research Center, Research Institute of Dental Sciences, Shahid Beheshti University of Medical Sciences, Tehran, Iran. Hauptthemen laut MEDLINE: Osteogenesis, Printing, Three-Dimensional, Tissue Scaffolds, Tissue Engineering. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 72 Literaturangaben. Gefördert von: This research was supported by a grant from the Dental Research Center, Shahid Beheshti University of Medical Sciences, Tehran, Iran (32248)..

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Incorporating autologous patient‐derived products has become imperative to enhance the continually improving outcomes in bone tissue engineering. With this objective in mind, this study aimed to evaluate the osteogenic potential of 3D‐printed allograft‐alginate‐gelatin scaffolds coated with stromal vascular fraction (SVF) and platelet‐rich fibrin (PRF). The primary goal was to develop a tissue‐engineered construct capable of facilitating efficient bone regeneration through the utilization of biomaterials with advantageous properties and patient‐derived products. To achieve this goal, 3D‐printed gelatin, allograft, and alginate scaffolds were utilized, along with stem cells derived from the buccal fat pad and human‐derived components (PRF, SVF). Cells were seeded onto scaffolds, both with and without SVF/PRF, and subjected to comprehensive assessments including adhesion, proliferation, differentiation (gene expression and protein secretion levels), penetration, and gene expression analysis over 14 days. The data was reported as mean ± standard deviation (SD). Two‐way or one‐way analysis of variance (ANOVA) was performed, followed by a Tukey post hoc test for multiple comparisons. Statistical significance was determined as a p value below 0.05. The scaffolds demonstrated structural integrity, and the addition of PRF coatings significantly enhanced cellular adhesion, proliferation, and differentiation compared to other groups. Gene expression analysis showed increased expression of osteogenic and angiogenic markers in the PRF‐coated scaffolds. These findings highlight the promising role of PRF‐coated scaffolds in promoting osteogenesis and facilitating bone tissue regeneration. This study emphasizes the development of patient‐specific tissue‐engineered constructs as a valuable approach for effective bone regeneration.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

OsteogenesisPrinting, Three-DimensionalTissue ScaffoldsTissue EngineeringPlatelet-Rich FibrinHydrogelsHumansGelatinAlginatesAdipose TissueCell DifferentiationBone RegenerationAllograftsCell ProliferationCell AdhesionCells, CulturedStromal Cells

Substanzen

GelatinAlginatesHydrogels

Autor:innen und Institutionen

  • Dental Research Center, Research Institute of Dental Sciences, Shahid Beheshti University of Medical Sciences, Tehran, Iran.
  • School of Dentistry, Shahid Beheshti University of Medical Sciences, Tehran, Iran.
  • Department of Pathology, Faculty of Veterinary Medicine, University of Tehran, Tehran, Iran.
  • Institute of Biomedical Research, University of Tehran, Tehran, Iran.
  • Department of Oral and Maxillofacial Surgery, School of Dentistry, Shahid Beheshti University of Medical Sciences, Tehran, Iran.

ORCID-Profile: Sahar Baniameri

Förderung

  • This research was supported by a grant from the Dental Research Center, Shahid Beheshti University of Medical Sciences, Tehran, Iran (32248).

Zitieren

APA

Baniameri, S., Aminianfar, H., Gharehdaghi, N., Yousefi-Koma, A. A., Mohaghegh, S., Nokhbatolfoghahaei, H., & Khojasteh, A. (2025). Tissue Engineering 3D‐Printed Scaffold Using Allograft/Alginate/Gelatin Hydrogels Coated With Platelet‐Rich Fibrin or Adipose Stromal Vascular Fraction Induces Osteogenesis In Vitro. Journal of Cellular Physiology. https://doi.org/10.1002/jcp.31497

Vancouver

Baniameri S, Aminianfar H, Gharehdaghi N, Yousefi-Koma AA, Mohaghegh S, Nokhbatolfoghahaei H, et al. Tissue Engineering 3D‐Printed Scaffold Using Allograft/Alginate/Gelatin Hydrogels Coated With Platelet‐Rich Fibrin or Adipose Stromal Vascular Fraction Induces Osteogenesis In Vitro. Journal of Cellular Physiology. 2025. doi:10.1002/jcp.31497

BibTeX
@article{Baniameri2025,
  author = {Baniameri, Sahar and Aminianfar, Hossein and Gharehdaghi, Niusha and Yousefi-Koma, Amir-Ali and Mohaghegh, Sadra and Nokhbatolfoghahaei, Hanieh and Khojasteh, Arash},
  title = {Tissue Engineering 3D‐Printed Scaffold Using Allograft/Alginate/Gelatin Hydrogels Coated With Platelet‐Rich Fibrin or Adipose Stromal Vascular Fraction Induces Osteogenesis In Vitro},
  journal = {Journal of Cellular Physiology},
  year = {2025},
  doi = {10.1002/jcp.31497}
}
Kostenlos starten →