EUVIMEDEUVIMED entdecken
Crossref

Infill Architecture Drives Early Osteogenesis in Additively Manufactured PCL Scaffolds With Controlled Porosity

Hisham Omar iD, Paulina Bargallo Gonzalez Lugo iD, Rachel Bonfini iD, Lekha Antala, Matthew Fainor iD, Sarah E Gullbrand iD, Michael W Hast iD

Journal of Biomedical Materials Research Part B: Applied Biomaterials · 2026-10 · 114 (10)

DOI: 10.1002/jbm.b.70164 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part B: Applied Biomaterials, online erschienen am 06.10.2026. Verfasst von Hisham Omar und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomedical Engineering, University of Delaware, Newark, Delaware, USA. Hauptthemen laut MEDLINE: Polyesters, Tissue Scaffolds, Osteogenesis. Die Arbeit nennt 44 Literaturangaben. Gefördert von: NIAMS NIH HHS, NIGMS NIH HHS, National Institute of Arthritis and Musculoskeletal and Skin Diseases.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Critical sized bone defects represent a significant challenge in orthopedic and reconstructive surgery. Additively manufactured (AM) bone scaffolds may be effective tools to treat these defects; however, the influence of infill architecture on early bone formation remains poorly characterized. This study used 3D‐printed biodegradable polycaprolactone (PCL) scaffolds to investigate the relationships between infill architecture, bone growth, and mechanical properties in a 4‐week in vitro experiment. Scaffolds containing bovine allograft were constructed with Gyroid and Honeycomb architectures at two porosity levels (40% and 60%). It was hypothesized that Gyroid scaffolds would accelerate early bone formation compared with Honeycomb designs. Gyroid architectures generally showed greater metabolic activity at weeks 3 and 4, with significant differences varying by porosity and time point. Micro‐CT analysis demonstrated significantly greater mineralized tissue volume and mineral density in Gyroid scaffolds compared with Honeycomb scaffolds at 4 weeks. Compressive mechanical testing indicated that Honeycomb structures were significantly stiffer and stronger than Gyroid scaffolds throughout the study. These results demonstrate that infill architecture significantly influences early bone formation independently of pore size and highlight a fundamental tradeoff between biological and mechanical performance in AM PCL scaffold design.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolyestersTissue ScaffoldsOsteogenesisAnimalsPorosityCattlePrinting, Three-DimensionalMaterials TestingX-Ray Microtomography

Stichwörter der Autor:innen

bone tissue engineering (BTE)fused deposition modeling (FDM)polycaprolactone (PCL)porosityscaffold architecturetriply periodic minimal surface (TPMS)

Substanzen

Polyesterspolycaprolactone

Autor:innen und Institutionen

  • Department of Biomedical Engineering, University of Delaware, Newark, Delaware, USA.
  • Department of Mechanical Engineering, University of Delaware, Newark, Delaware, USA.
  • Department of Genetics, Stanford University School of Medicine, Stanford, California, USA.
  • McKay Orthopaedic Research Lab, Department of Orthopaedic Surgery, University of Pennsylvania, Philadelphia, Pennsylvania, USA.
  • Translational Musculoskeletal Research Center, CMC VA Medical Center, Philadelphia, Pennsylvania, USA.
  • Department of Bioengineering, University of Pennsylvania, Philadelphia, Pennsylvania, USA.

ORCID-Profile: Hisham Omar, Paulina Bargallo Gonzalez Lugo, Rachel Bonfini, Matthew Fainor, Sarah E Gullbrand, Michael W Hast

Förderung

  • NIAMS NIH HHS
  • NIGMS NIH HHS
  • National Institute of Arthritis and Musculoskeletal and Skin Diseases
  • National Institute of General Medical Sciences

Zitieren

APA

Omar, H., Lugo, P. B. G., Bonfini, R., Antala, L., Fainor, M., Gullbrand, S. E., & Hast, M. W. (2026). Infill Architecture Drives Early Osteogenesis in Additively Manufactured PCL Scaffolds With Controlled Porosity. Journal of Biomedical Materials Research Part B: Applied Biomaterials, 114(10). https://doi.org/10.1002/jbm.b.70164

Vancouver

Omar H, Lugo PBG, Bonfini R, Antala L, Fainor M, Gullbrand SE, et al. Infill Architecture Drives Early Osteogenesis in Additively Manufactured PCL Scaffolds With Controlled Porosity. Journal of Biomedical Materials Research Part B: Applied Biomaterials. 2026;114(10). doi:10.1002/jbm.b.70164

BibTeX
@article{Omar2026,
  author = {Omar, Hisham and Lugo, Paulina Bargallo Gonzalez and Bonfini, Rachel and Antala, Lekha and Fainor, Matthew and Gullbrand, Sarah E and Hast, Michael W},
  title = {Infill Architecture Drives Early Osteogenesis in Additively Manufactured PCL Scaffolds With Controlled Porosity},
  journal = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  year = {2026},
  volume = {114},
  number = {10},
  doi = {10.1002/jbm.b.70164}
}
Kostenlos starten →