EUVIMEDEUVIMED entdecken
Crossref

Large‐Pore 3D ‐Printed PLA / HA / CDHA Gyroid Scaffolds for Bone Regeneration: Effect of Unit‐Cell Period in a Rabbit Calvarial Defect Model

Milda Vitosyte iD, Egidijus Simoliunas, Milda Alksne, Marius Didziokas, Carlos Manuel Martínez-Cáceres, Victoria Martínez Abenza, Mantas Liudvinaitis, Dovile Proskute, Vygandas Rutkunas, Ieva Gendviliene

Journal of Biomedical Materials Research Part B: Applied Biomaterials · 2026-07 · 114 (7)

DOI: 10.1002/jbm.b.70128 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part B: Applied Biomaterials, online erschienen am 07.07.2026. Verfasst von Milda Vitosyte und 9 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Odontology, Faculty of Medicine, Vilnius University, Vilnius, Lithuania. Hauptthemen laut MEDLINE: Bone Regeneration, Tissue Scaffolds, Printing, Three-Dimensional, Skull. Die Arbeit nennt 53 Literaturangaben. Gefördert von: Vilnius University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

To evaluate late‐stage bone regeneration in rabbit calvarial critical‐size defects treated with 3D‐printed PLA/HA/CDHA gyroid scaffolds with unit‐cell periods of 0.9 or 1.2 mm, versus empty defects. In this randomized exploratory within‐animal preclinical study, 12 calvarial defects were created in New Zealand White rabbits and allocated to PLA/HA/CDHA gyroid scaffolds with a 0.9‐mm unit‐cell period ( n = 5), PLA/HA/CDHA gyroid scaffolds with a 1.2‐mm unit‐cell period ( n = 4), or empty negative controls ( n = 3). Healing was assessed after 12 weeks by micro‐computed tomography and histomorphometry. At 12 weeks there was no statistically detectable difference in regenerated bone volume between groups; given the limited sample size and wide variances, this finding does not constitute evidence of equivalence. Both scaffold designs supported bone formation within the defects and showed descriptively thicker peripheral bone rims on histology than empty controls. Histomorphometric new bone area was 2.30 ± 1.16 mm 2 in the 0.9‐mm group and 2.43 ± 1.15 mm 2 in the 1.2‐mm group, compared with 1.17 ± 1.10 mm 2 in controls. Vascularized surface was descriptively higher in scaffold‐treated defects, with the highest mean value in the 1.2‐mm group. Spatial analyses suggested more center‐directed bone advancement in scaffold‐treated defects, particularly in the 1.2‐mm group. Spatial analyses suggested a scaffold‐associated bottom‐to‐top (dural‐side) pattern of bone advancement, while the two scaffold architectures performed similarly across bone and vascular outcomes. Although bone volume did not differ significantly between the 0.9‐ and 1.2‐mm groups, equivalence cannot be inferred. Further longitudinal studies are needed to optimize architected composite scaffolds for craniofacial bone regeneration and dental augmentation.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Bone RegenerationTissue ScaffoldsPrinting, Three-DimensionalSkullPolyestersDurapatiteAnimalsRabbitsX-Ray MicrotomographyPorosityMale

Stichwörter der Autor:innen

3D‐printed scaffoldbiomaterialsbone regenerationcalvarial defectguided bone regenerationhydroxyapatitevascularization

Substanzen

Polyesterspoly(lactide)Durapatite

Autor:innen und Institutionen

  • Institute of Odontology, Faculty of Medicine, Vilnius University, Vilnius, Lithuania.
  • Institute of Biochemistry, Life Sciences Center, Vilnius University, Vilnius, Lithuania.
  • Department of Chemistry and Interdisciplinary Nanoscience Centre (iNano), Aarhus University, Aarhus, Denmark.
  • Departamento de Anatomía y Anatomía Patológica Comparadas, Universidad de Murcia, Murcia, Spain.
  • Plataforma de patología, IMIB-Pascual Parrilla, Murcia, Spain.
  • Department of Pediatric Otorhinolaryngology and Santaros Departament of Maxillofacial Surgery, Vilnius University Hospital Santaros Clinics, Vilnius, Lithuania.

ORCID-Profile: Milda Vitosyte

Förderung

  • Vilnius University

Zitieren

APA

Vitosyte, M., Simoliunas, E., Alksne, M., Didziokas, M., Martínez-Cáceres, C. M., Abenza, V. M., Liudvinaitis, M., Proskute, D., Rutkunas, V., & Gendviliene, I. (2026). Large‐Pore 3D ‐Printed PLA / HA / CDHA Gyroid Scaffolds for Bone Regeneration: Effect of Unit‐Cell Period in a Rabbit Calvarial Defect Model. Journal of Biomedical Materials Research Part B: Applied Biomaterials, 114(7). https://doi.org/10.1002/jbm.b.70128

Vancouver

Vitosyte M, Simoliunas E, Alksne M, Didziokas M, Martínez-Cáceres CM, Abenza VM, et al. Large‐Pore 3D ‐Printed PLA / HA / CDHA Gyroid Scaffolds for Bone Regeneration: Effect of Unit‐Cell Period in a Rabbit Calvarial Defect Model. Journal of Biomedical Materials Research Part B: Applied Biomaterials. 2026;114(7). doi:10.1002/jbm.b.70128

BibTeX
@article{Vitosyte2026,
  author = {Vitosyte, Milda and Simoliunas, Egidijus and Alksne, Milda and Didziokas, Marius and Martínez-Cáceres, Carlos Manuel and Abenza, Victoria Martínez and Liudvinaitis, Mantas and Proskute, Dovile and Rutkunas, Vygandas and Gendviliene, Ieva},
  title = {Large‐Pore 3D ‐Printed PLA / HA / CDHA Gyroid Scaffolds for Bone Regeneration: Effect of Unit‐Cell Period in a Rabbit Calvarial Defect Model},
  journal = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  year = {2026},
  volume = {114},
  number = {7},
  doi = {10.1002/jbm.b.70128}
}
Kostenlos starten →