Evaluation of Different Geometry Poly(L‐Lactide‐Co‐Glycolide‐Co‐Trimethylene Carbonate Oligomer) Scaffolds Fabricated by Material Extrusion 3D Printing for Adipose Derived Stem Cells Culture
Journal of Biomedical Materials Research Part B: Applied Biomaterials · 2025
DOI: 10.1002/jbm.b.35580 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part B: Applied Biomaterials, 2025. Verfasst von Piotr Paduszyński und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biopharmacy, Faculty of Pharmaceutical Sciences in Sosnowiec, Medical University of Silesia, Katowice, Poland. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Tissue Scaffolds, Adipose Tissue, Stem Cells. Die Arbeit nennt 64 Literaturangaben. Gefördert von: Śląski Uniwersytet Medyczny, Medical University of Silesia in Katowice.
Abstract (Originalsprache)
The combination of stem cells, growth factors, and biomaterials has driven significant advancements in tissue engineering. Depending on the specific tissue requiring regeneration, the scaffold structure and cell type must be carefully selected. Adipose‐derived stem cells (ADSC) have garnered considerable interest due to their ease of isolation and high differentiation potential. However, cellular components alone are often insufficient for complete tissue regeneration, making the selection of an appropriate scaffold structure a critical factor. Modern additive manufacturing techniques enable the precise design and fabrication of scaffolds with tailored properties and architectures. This study presents comprehensive research in tissue engineering, polymer chemistry, and polymer processing, focusing on the fabrication of scaffolds with varying architectures for ADSC culture using additive manufacturing. A poly(L‐lactide‐co‐glycolide‐co‐trimethylene carbonate oligomer) (PLGA‐oTMC) terpolymer of defined molar composition and microstructure was synthesized and processed into a filament suitable for 3D printing via the Material Extrusion (formerly Fused Deposition Modeling) method, which has not yet been demonstrated in scientific research. Optimized molar composition, microstructure, and average molar mass of PLGA‐oTMC ensured an appropriate melt viscosity, facilitating 3D printing under conditions that minimized polymer thermal degradation. This, in turn, enabled effective cell culture. The resulting scaffolds exhibited favorable biocompatibility, as evidenced by high ADSC viability and proliferation capacity. However, variations in scaffold architecture influenced ADSC colonization, with certain designs promoting more effective adhesion and cytoskeletal organization. The good viability and proliferative ability of ADSC strongly suggest that PLGA‐oTMC scaffolds, combined with stem cells, show great promise for the engineering of damaged tissues such as bone or cartilage.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Substanzen
Autor:innen und Institutionen
- Department of Biopharmacy, Faculty of Pharmaceutical Sciences in Sosnowiec, Medical University of Silesia, Katowice, Poland.
- Centre of Polymer and Carbon Materials of Polish Academy of Sciences, Zabrze, Poland.
- Department of Pharmaceutical Chemistry, Faculty of Pharmaceutical Sciences in Sosnowiec, Medical University of Silesia, Katowice, Poland.
ORCID-Profile: Piotr Paduszyński, Jakub Włodarczyk, Jakub Rok, Małgorzata Pastusiak, Zuzanna Rzepka, Arkadiusz Orchel, Dorota Wrześniok, Janusz Kasperczyk
Förderung
- Śląski Uniwersytet Medyczny
- Medical University of Silesia in Katowice
Zitieren
APA
Paduszyński, P., Włodarczyk, J., Rok, J., Pastusiak, M., Rzepka, Z., Ochab, A., Karpeta-Jarząbek, P., Orchel, A., Wrześniok, D., & Kasperczyk, J. (2025). Evaluation of Different Geometry Poly(L‐Lactide‐Co‐Glycolide‐Co‐Trimethylene Carbonate Oligomer) Scaffolds Fabricated by Material Extrusion 3D Printing for Adipose Derived Stem Cells Culture. Journal of Biomedical Materials Research Part B: Applied Biomaterials. https://doi.org/10.1002/jbm.b.35580
Vancouver
Paduszyński P, Włodarczyk J, Rok J, Pastusiak M, Rzepka Z, Ochab A, et al. Evaluation of Different Geometry Poly(L‐Lactide‐Co‐Glycolide‐Co‐Trimethylene Carbonate Oligomer) Scaffolds Fabricated by Material Extrusion 3D Printing for Adipose Derived Stem Cells Culture. Journal of Biomedical Materials Research Part B: Applied Biomaterials. 2025. doi:10.1002/jbm.b.35580
BibTeX
@article{Paduszyski2025,
author = {Paduszyński, Piotr and Włodarczyk, Jakub and Rok, Jakub and Pastusiak, Małgorzata and Rzepka, Zuzanna and Ochab, Agnieszka and Karpeta-Jarząbek, Paulina and Orchel, Arkadiusz and Wrześniok, Dorota and Kasperczyk, Janusz},
title = {Evaluation of Different Geometry Poly(L‐Lactide‐Co‐Glycolide‐Co‐Trimethylene Carbonate Oligomer) Scaffolds Fabricated by Material Extrusion 3D Printing for Adipose Derived Stem Cells Culture},
journal = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
year = {2025},
doi = {10.1002/jbm.b.35580}
}
EUVIMED