EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

TiO 2 nanotubes with customized diameters for local drug delivery systems

Sayaka Miyabe iD, Yushi Fujinaga, Hiroaki Tsuchiya iD, Shinji Fujimoto iD

Journal of Biomedical Materials Research Part B: Applied Biomaterials · 2024

DOI: 10.1002/jbm.b.35445 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part B: Applied Biomaterials, 2024. Verfasst von Sayaka Miyabe und 3 weiteren Autor:innen. Beteiligte Einrichtung: Division of Materials and Manufacturing Science, Graduate School of Engineering, Osaka University, Osaka, Japan. Hauptthemen laut MEDLINE: Titanium, Nanotubes. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this study, we evaluated the drug release behavior of diameter customized TiO 2 nanotube layers fabricated by anodization with various applied voltage sequences: conventional constant applied potentials of 20 V (45 nm) and 60 V (80 nm), a 20/60 V stepped potential (50 nm [two‐diameter]), and a 20–60 V swept potential (49 nm [full‐tapered]) (values in parentheses indicate the inner tube diameter at the top part of nanotube layers). The structures of the 50 nm (two‐diameter) and 49 nm (full‐tapered) samples had smaller inner diameters at the top part of nanotube layers than that of the 80 nm sample, while the outer diameters at the bottom part of nanotube layers were almost the same size as the 80 nm sample. The 80 nm sample, which had the largest nanotube diameter and length, exhibited the greatest burst release, followed by the 50 nm (two‐diameter), 49 nm (full‐tapered), and 45 nm samples. The initial burst released drug amounts and release rates from the 50 nm (two‐diameter) and 49 nm (full‐tapered) samples were significantly suppressed by the smaller tube top. On the other hand, the largest proportion of the slow released drug amount to the total released drug amount was observed for the 50 nm (two‐diameter) sample. Thus, 50 nm (two‐diameter) achieved suppressed initial burst release and large storage capacity. Therefore, this study has, for the first time, applied TiO 2 nanotube layers with modulated diameters (two‐diameter and full‐tapered) to the realization of a localized drug delivery system (LDDS) with customized drug release properties.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

TitaniumNanotubesDrug Delivery SystemsDrug LiberationParticle Size

Stichwörter der Autor:innen

TiO2 nanotubesanodizationlocal drug delivery systemoxide nanotubes

Substanzen

Titaniumtitanium dioxide

Autor:innen und Institutionen

  • Division of Materials and Manufacturing Science, Graduate School of Engineering, Osaka University, Osaka, Japan.

ORCID-Profile: Sayaka Miyabe, Hiroaki Tsuchiya, Shinji Fujimoto

Zitieren

APA

Miyabe, S., Fujinaga, Y., Tsuchiya, H., & Fujimoto, S. (2024). TiO 2 nanotubes with customized diameters for local drug delivery systems. Journal of Biomedical Materials Research Part B: Applied Biomaterials. https://doi.org/10.1002/jbm.b.35445

Vancouver

Miyabe S, Fujinaga Y, Tsuchiya H, Fujimoto S. TiO 2 nanotubes with customized diameters for local drug delivery systems. Journal of Biomedical Materials Research Part B: Applied Biomaterials. 2024. doi:10.1002/jbm.b.35445

BibTeX
@article{Miyabe2024,
  author = {Miyabe, Sayaka and Fujinaga, Yushi and Tsuchiya, Hiroaki and Fujimoto, Shinji},
  title = {TiO 2 nanotubes with customized diameters for local drug delivery systems},
  journal = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  year = {2024},
  doi = {10.1002/jbm.b.35445}
}
Kostenlos starten →