EUVIMEDEUVIMED entdecken
Crossref

Mechanically suitable and osteoinductive 3D ‐printed composite scaffolds with hydroxyapatite nanoparticles having diverse morphologies for bone tissue engineering

Michał Wojasiński iD, Rafał Podgórski iD, Piotr Kowalczyk iD, Joanna Latocha iD, Kornel Prystupiuk iD, Oliwia Janowska, Stanisław Gierlotka iD, Monika Staniszewska iD, Tomasz Ciach iD, Paweł Sobieszuk iD

Journal of Biomedical Materials Research Part B: Applied Biomaterials · 2024

DOI: 10.1002/jbm.b.35409 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part B: Applied Biomaterials, 2024. Verfasst von Michał Wojasiński und 9 weiteren Autor:innen. Beteiligte Einrichtung: Laboratory of Nanohydroxyapatite (LabOFn), Faculty of Chemical and Process Engineering, Department of Biotechnology and Bioprocess Engineering, Warsa…. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Tissue Scaffolds, Durapatite, Tissue Engineering. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 57 Literaturangaben. Gefördert von: Research was funded by (POB Biotechnology and Biomedical Engineering) of Warsaw University of Technology within the Excellence Initiative: Research University….

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The challenge of integrating hydroxyapatite nanoparticles (nHAp) with polymers is hindered by the conflict between the hydrophilic and hygroscopic properties of nHAp and the hydrophobic properties of polymers. This conflict particularly affects the materials when calcium phosphates, including nHAp, are used as a filler in composites in thermal processing applications such as 3D printing with fused filament fabrication (FFF). To overcome this, we propose a one‐step surface modification of nHAp with calcium stearate monolayer. Moreover, to build the scaffold with suitable mechanical strength, we tested the addition of nHAp with diverse morphology—spherical, plate‐ and rod‐like nanoparticles. Our analysis showed that the composite of polycaprolactone (PCL) reinforced with nHAp with rod and plate morphologies modified with calcium stearate monolayer exhibited a significant increase in compressive strength. However, composites with spherical nHAp added to PCL showed a significant reduction in compressive modulus and compressive strength, but both parameters were within the applicability range of hard tissue scaffolds. None of the tested composite scaffolds showed cytotoxicity in L929 murine fibroblasts or MG‐63 human osteoblast‐like cells, supporting the proliferation of the latter. Additionally, PCL/nHAp scaffolds reinforced with spherical nHAp caused osteoactivation of bone marrow human mesenchymal stem cells, as indicated by alkaline phosphatase activity and COL1, RUNX2, and BGLAP expression. These results suggest that the calcium stearate monolayer on the surface of the nHAp particles allows the production of polymer/nHAp composites suitable for hard tissue engineering and personalized implant production in 3D printing using the FFF technique.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalTissue ScaffoldsDurapatiteTissue EngineeringNanoparticlesMiceAnimalsHumansCell LinePolyestersOsteoblastsOsteogenesisMaterials Testing

Stichwörter der Autor:innen

compositehydroxyapatitemechanical propertiesmesenchymal stem cellsnanoparticle

Substanzen

DurapatitePolyesterspolycaprolactone

Autor:innen und Institutionen

  • Laboratory of Nanohydroxyapatite (LabOFn), Faculty of Chemical and Process Engineering, Department of Biotechnology and Bioprocess Engineering, Warsaw University of Technology, Warsaw, Poland.
  • Laboratory of Nanostructures, Institute of High Pressure Physics, Polish Academy of Sciences, Warsaw, Poland.
  • Centre for Advanced Materials and Technologies CEZAMAT, Warsaw, Poland.

ORCID-Profile: Michał Wojasiński, Rafał Podgórski, Piotr Kowalczyk, Joanna Latocha, Kornel Prystupiuk, Stanisław Gierlotka, Monika Staniszewska, Tomasz Ciach, Paweł Sobieszuk

Förderung

  • Research was funded by (POB Biotechnology and Biomedical Engineering) of Warsaw University of Technology within the Excellence Initiative: Research University…

Zitieren

APA

Wojasiński, M., Podgórski, R., Kowalczyk, P., Latocha, J., Prystupiuk, K., Janowska, O., Gierlotka, S., Staniszewska, M., Ciach, T., & Sobieszuk, P. (2024). Mechanically suitable and osteoinductive 3D ‐printed composite scaffolds with hydroxyapatite nanoparticles having diverse morphologies for bone tissue engineering. Journal of Biomedical Materials Research Part B: Applied Biomaterials. https://doi.org/10.1002/jbm.b.35409

Vancouver

Wojasiński M, Podgórski R, Kowalczyk P, Latocha J, Prystupiuk K, Janowska O, et al. Mechanically suitable and osteoinductive 3D ‐printed composite scaffolds with hydroxyapatite nanoparticles having diverse morphologies for bone tissue engineering. Journal of Biomedical Materials Research Part B: Applied Biomaterials. 2024. doi:10.1002/jbm.b.35409

BibTeX
@article{Wojasiski2024,
  author = {Wojasiński, Michał and Podgórski, Rafał and Kowalczyk, Piotr and Latocha, Joanna and Prystupiuk, Kornel and Janowska, Oliwia and Gierlotka, Stanisław and Staniszewska, Monika and Ciach, Tomasz and Sobieszuk, Paweł},
  title = {Mechanically suitable and osteoinductive 3D ‐printed composite scaffolds with hydroxyapatite nanoparticles having diverse morphologies for bone tissue engineering},
  journal = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  year = {2024},
  doi = {10.1002/jbm.b.35409}
}
Kostenlos starten →