EUVIMEDEUVIMED entdecken
Open Access

Internal surface modification of additively manufactured macroporous TiAl6V4 biomimetic implants via a calciothermic reaction‐based process and osteogenic in vivo responses

Michael B Berger, D Joshua Cohen iD, Jingyao Deng, Pavan Srivas, Barbara D Boyan iD, Kenneth H Sandhage, Zvi Schwartz

Journal of Biomedical Materials Research Part B: Applied Biomaterials · 2024

DOI: 10.1002/jbm.b.35322 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part B: Applied Biomaterials, 2024. Verfasst von Michael B Berger und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Biomedical Engineering, Virginia Commonwealth University, Richmond, Virginia, USA. Hauptthemen laut MEDLINE: Osteogenesis, Titanium. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 50 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NIAMS NIH HHS, NIH HHS, National Institutes of Health.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Three‐dimensional macroporous titanium–aluminum–vanadium (TiAl6V4) implants produced by additive manufacturing (AM) can be grit blasted (GB) to yield microtextured exterior surfaces, with additional micro/nano‐scale surface features provided by subsequent acid etching (AE). However, the line‐of‐sight nature of GB causes the topography of exterior GB + AE‐modified surfaces to differ from internal GB‐inaccessible surfaces. Previous in vitro studies using dense TiAl6V4 substrates indicated that a nonline‐of‐sight, calciothermic‐reaction (CaR)‐based process provided homogeneous osteogenic nanotextures on GB + AE surfaces, suggesting it could be used to achieve a homogeneous nanotopography on external and internal surfaces of macroporous AM constructs. Macroporous TiAl6V4 (3D) constructs were produced by direct laser melting and modified by GB + AE, with the CaR process then applied to 50% of constructs (3DCaR). The CaR process yielded nanoporous/nanorough internal surfaces throughout the macroporous constructs. Skeletally mature, male Sprague–Dawley rats were implanted with these constructs using a cranial on‐lay model. Prior to implantation, a Cu++‐free click hydrogel was applied to half of the constructs (3D + H, 3DCaR + H) to act as a challenge to osseointegration. Osseointegration was compared between the four implant groups (3D, 3DCaR, 3D + H, 3DCaR + H) at 4w. 3D + H implants exhibited lower bone volume (BV) and percent bone ingrowth (%BI) than the 3D implants. In contrast, osseointegrated 3DCaR + H implants had similar BV and %BI as the 3DCaR implants. Implant pull‐off forces correlated with these results. In vitro analyses indicated that human bone marrow stromal cells (MSCs) exhibited enhanced production of osteoblast differentiation markers and factors associated with osteogenesis when grown on CaR‐modified 3D substrates relative to control (TCPS) substrates. This work confirms that the CaR process provides osteogenic nanotextures on internal surfaces of macroporous 3D implants, and suggests that CaR‐modified surfaces can promote osseointegration in cases where osteogenesis is impaired.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

OsteogenesisTitaniumRatsAnimalsMaleHumansRats, Sprague-DawleyAluminumVanadiumBiomimeticsOsseointegrationSurface Properties

Stichwörter der Autor:innen

calciothermic reactionhydrogelosseointegrationsurface modificationtitanium-based implants

Substanzen

TitaniumAluminumVanadium

Autor:innen und Institutionen

  • Department of Biomedical Engineering, Virginia Commonwealth University, Richmond, Virginia, USA.
  • School of Materials Engineering, Purdue University, West Lafayette, Indiana, USA.
  • Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology and Emory University, Atlanta, Georgia, USA.
  • Department of Periodontology, University of Texas Health Science Center at San Antonio, San Antonio, Texas, USA.

ORCID-Profile: D Joshua Cohen, Barbara D Boyan

Förderung

  • NIAMS NIH HHS
  • NIH HHS
  • National Institutes of Health

Zitieren

APA

Berger, M. B., Cohen, D. J., Deng, J., Srivas, P., Boyan, B. D., Sandhage, K. H., & Schwartz, Z. (2024). Internal surface modification of additively manufactured macroporous TiAl6V4 biomimetic implants via a calciothermic reaction‐based process and osteogenic in vivo responses. Journal of Biomedical Materials Research Part B: Applied Biomaterials. https://doi.org/10.1002/jbm.b.35322

Vancouver

Berger MB, Cohen DJ, Deng J, Srivas P, Boyan BD, Sandhage KH, et al. Internal surface modification of additively manufactured macroporous TiAl6V4 biomimetic implants via a calciothermic reaction‐based process and osteogenic in vivo responses. Journal of Biomedical Materials Research Part B: Applied Biomaterials. 2024. doi:10.1002/jbm.b.35322

BibTeX
@article{Berger2024,
  author = {Berger, Michael B and Cohen, D Joshua and Deng, Jingyao and Srivas, Pavan and Boyan, Barbara D and Sandhage, Kenneth H and Schwartz, Zvi},
  title = {Internal surface modification of additively manufactured macroporous TiAl6V4 biomimetic implants via a calciothermic reaction‐based process and osteogenic in vivo responses},
  journal = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  year = {2024},
  doi = {10.1002/jbm.b.35322}
}
Kostenlos starten →