EUVIMEDEUVIMED entdecken
Crossref

Integrating Near‐Field Direct‐Writing 3D Printing and Layer‐By‐Layer Self‐Assembly to Construct Electroactive Anisotropic Scaffolds for Neural Tissue Engineering

Chao Shen, Baiheng Lv, Yujun Zeng, Ronghan Wu, Peng Ding, Juqing Song iD

Journal of Biomedical Materials Research Part A · 2026-08 · 114 (8)

DOI: 10.1002/jbm.a.70141 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part A, online erschienen am 05.08.2026. Verfasst von Chao Shen und 5 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Dongguan University of Technology, Dongguan, China. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Tissue Scaffolds, Tissue Engineering, Nerve Tissue. Die Arbeit nennt 62 Literaturangaben. Gefördert von: Department of Education of Guangdong Province, the Dongguan Municipal Bureau of Science and Technology.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

All current clinical treatments for peripheral nerve injury (PNI), including end‐to‐end suturing, allografts, non‐surgical management, and autografts, suffer from inherent limitations that prevent adequate functional recovery. To address this challenge, we fabricated anisotropic polycaprolactone (PCL) mesh scaffolds via near‐field direct‐writing (NFDW) 3D printing for neural tissue engineering. To endow the scaffolds with electroactivity, a layer‐by‐layer (LbL) self‐assembly technique was employed to coat polyethylenimine/graphene oxide (PEI/GO), followed by in situ reduction to form conductive reduced graphene oxide/PCL (RGO/PCL) composite scaffolds. Systematic characterization demonstrated that scaffolds coated with 10 LbL cycles achieved an optimal balance, maintaining a favorable topological structure while exhibiting significantly enhanced electrical conductivity, mechanical properties, and hydrophilicity. Biological evaluations confirmed the excellent biocompatibility of the composite scaffolds, which effectively promoted the adhesion, spreading, and neural differentiation of PC12‐L cells. Notably, scaffolds with 10 and 15 coating cycles upregulated β‐tubulin III expression and facilitated the formation of axon‐like structures. Furthermore, the composite scaffold was successfully fashioned into a nerve conduit, highlighting its potential for peripheral nerve repair. This work offers a promising strategy for constructing electroactive, biomimetic scaffolds to enhance neural regeneration.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalTissue ScaffoldsTissue EngineeringNerve TissueAnimalsRatsPC12 CellsPolyestersAnisotropyGraphiteElectric ConductivityPolyethyleneimineCell Differentiation

Stichwörter der Autor:innen

anisotropic scaffoldselectroactive nerve conduitsnear‐field direct‐writing 3D printing

Substanzen

polycaprolactonePolyestersGraphitegraphene oxidePolyethyleneimine

Autor:innen und Institutionen

  • School of Mechanical Engineering, Dongguan University of Technology, Dongguan, China.
  • China Nuclear Power Technology Research Institute Co. Ltd, Shenzhen, China.

ORCID-Profile: Juqing Song

Förderung

  • Department of Education of Guangdong Province
  • the Dongguan Municipal Bureau of Science and Technology

Zitieren

APA

Shen, C., Lv, B., Zeng, Y., Wu, R., Ding, P., & Song, J. (2026). Integrating Near‐Field Direct‐Writing 3D Printing and Layer‐By‐Layer Self‐Assembly to Construct Electroactive Anisotropic Scaffolds for Neural Tissue Engineering. Journal of Biomedical Materials Research Part A, 114(8). https://doi.org/10.1002/jbm.a.70141

Vancouver

Shen C, Lv B, Zeng Y, Wu R, Ding P, Song J. Integrating Near‐Field Direct‐Writing 3D Printing and Layer‐By‐Layer Self‐Assembly to Construct Electroactive Anisotropic Scaffolds for Neural Tissue Engineering. Journal of Biomedical Materials Research Part A. 2026;114(8). doi:10.1002/jbm.a.70141

BibTeX
@article{Shen2026,
  author = {Shen, Chao and Lv, Baiheng and Zeng, Yujun and Wu, Ronghan and Ding, Peng and Song, Juqing},
  title = {Integrating Near‐Field Direct‐Writing 3D Printing and Layer‐By‐Layer Self‐Assembly to Construct Electroactive Anisotropic Scaffolds for Neural Tissue Engineering},
  journal = {Journal of Biomedical Materials Research Part A},
  year = {2026},
  volume = {114},
  number = {8},
  doi = {10.1002/jbm.a.70141}
}
Kostenlos starten →