EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Extrusion 3D‐printed tricalcium phosphate‐polycaprolactone biocomposites for quercetin‐KCl delivery in bone tissue engineering

Connor Toulou iD, Vishal Sharad Chaudhari iD, Susmita Bose iD

Journal of Biomedical Materials Research Part A · 2024

DOI: 10.1002/jbm.a.37692 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part A, 2024. Verfasst von Connor Toulou und 2 weiteren Autor:innen. Beteiligte Einrichtung: W. M. Keck Biomedical Materials Research Laboratory, School of Mechanical and Materials Engineering, Washington State University, Pullman, Washington…. Hauptthemen laut MEDLINE: Quercetin, Polyesters, Printing, Three-Dimensional, Tissue Engineering. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 53 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: NIDCR NIH HHS, NIAMS NIH HHS, National Institute of Dental and Craniofacial Research.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Critical‐sized bone defects pose a significant challenge in advanced healthcare due to limited bone tissue regenerative capacity. The complex interplay of numerous overlapping variables hinders the development of multifunctional biocomposites. Phytochemicals show promise in promoting bone growth, but their dose‐dependent nature and physicochemical properties halt clinical use. To develop a comprehensive solution, a 3D‐printed (3DP) extrusion‐based tricalcium phosphate‐polycaprolactone (TCP‐PCL) scaffold is augmented with quercetin and potassium chloride (KCl). This composite material demonstrates a compressive strength of 30 MPa showing promising stability for low load‐bearing applications. Quercetin release from the scaffold follows a biphasic pattern that persists for up to 28 days, driven via diffusion‐mediated kinetics. The incorporation of KCl allows for tunable degradation rates of scaffolds and prevents the initial rapid release. Functionalization of scaffolds facilitates the attachment and proliferation of human fetal osteoblasts (hfOB), resulting in a 2.1‐fold increase in cell viability. Treated scaffolds exhibit a 3‐fold reduction in osteosarcoma (MG‐63) cell viability as compared to untreated substrates. Ruptured cell morphology and decreased mitochondrial membrane potential indicate the antitumorigenic potential. Scaffolds loaded with quercetin and quercetin‐KCl (Q‐KCl) demonstrate 76% and 89% reduction in bacterial colonies of Staphylococcus aureus , respectively. This study provides valuable insights as a promising strategy for bone tissue engineering (BTE) in orthopedic repair.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

QuercetinPolyestersPrinting, Three-DimensionalTissue EngineeringCalcium PhosphatesTissue ScaffoldsHumansBone and BonesOsteoblastsCell SurvivalCell Line, Tumor

Stichwörter der Autor:innen

biocompositesbone scaffoldsextrusion 3D‐printingquercetin

Substanzen

QuercetinPolyesterspolycaprolactoneCalcium Phosphatestricalcium phosphate

Autor:innen und Institutionen

  • W. M. Keck Biomedical Materials Research Laboratory, School of Mechanical and Materials Engineering, Washington State University, Pullman, Washington, USA.

ORCID-Profile: Connor Toulou, Vishal Sharad Chaudhari, Susmita Bose

Förderung

  • NIDCR NIH HHS
  • NIAMS NIH HHS
  • National Institute of Dental and Craniofacial Research

Zitieren

APA

Toulou, C., Chaudhari, V. S., & Bose, S. (2024). Extrusion 3D‐printed tricalcium phosphate‐polycaprolactone biocomposites for quercetin‐KCl delivery in bone tissue engineering. Journal of Biomedical Materials Research Part A. https://doi.org/10.1002/jbm.a.37692

Vancouver

Toulou C, Chaudhari VS, Bose S. Extrusion 3D‐printed tricalcium phosphate‐polycaprolactone biocomposites for quercetin‐KCl delivery in bone tissue engineering. Journal of Biomedical Materials Research Part A. 2024. doi:10.1002/jbm.a.37692

BibTeX
@article{Toulou2024,
  author = {Toulou, Connor and Chaudhari, Vishal Sharad and Bose, Susmita},
  title = {Extrusion 3D‐printed tricalcium phosphate‐polycaprolactone biocomposites for quercetin‐KCl delivery in bone tissue engineering},
  journal = {Journal of Biomedical Materials Research Part A},
  year = {2024},
  doi = {10.1002/jbm.a.37692}
}
Kostenlos starten →