EUVIMEDEUVIMED entdecken
Crossref

Accelerated aging studies of UHMWPE. I. Effect of resin, processing, and radiation environment on resistance to mechanical degradation

A A Edidin, M P Herr, M L Villarraga, J Muth, S S Yau, S M Kurtz

Journal of Biomedical Materials Research · 2002-08 · 61 (2) · 312-322

DOI: 10.1002/jbm.10135 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research, online erschienen am 29.04.2002. Verfasst von A A Edidin und 5 weiteren Autor:innen. Beteiligte Einrichtung: Stryker Howmedica Osteonics Corporation, 300 Commerce Court, Mahwah, New Jersey 07430, USA. edidin@warwick.net.com. Hauptthemen laut MEDLINE: Materials Testing. Die Arbeit wurde bisher 35-mal zitiert (Crossref) und nennt 24 Literaturangaben.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The resin and processing route have been identified as potential variables influencing the mechanical behavior, and hence the clinical performance, of ultra‐high molecular weight polyethylene (UHMWPE) orthopedic components. Researchers have reported that components fabricated from 1900 resin may oxidize to a lesser extent than components fabricated from GUR resin during shelf aging after gamma sterilization in air. Conflicting reports on the oxidation resistance for 1900 raise the question of whether resin or manufacturing method, or an interaction between resin and manufacturing method, influences the mechanical behavior of UHMWPE. We conducted a series of accelerated aging studies (no aging, aging in oxygen or in nitrogen) to systematically examine the influence of resin (GUR or 1900), manufacturing method (bulk compression molding or extrusion), and sterilization method (none, in air, or in nitrogen) on the mechanical behavior of UHMWPE. The small punch testing technique was used to evaluate the mechanical behavior of the materials, and Fourier transform infrared spectroscopy was used to characterize the oxidation in selected samples. Our study showed that the sterilization environment, aging condition, and specimen location (surface or subsurface) significantly affected the mechanical behavior of UHMWPE. Each of the three polyethylenes evaluated seem to degrade according to a similar pathway after artificial aging in oxygen and gamma irradiation in air. The initial ability of the materials to exhibit post‐yield strain hardening was significantly compromised by degradation. In general, there were only minor differences in the aging behavior of molded and extruded GUR 1050, whereas the molded 1900 material seemed to degrade slightly faster than either of the 1050 materials. © 2002 Wiley Periodicals, Inc. J Biomed Mater Res 61: 312–322, 2002

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Materials TestingBiocompatible MaterialsEquipment Failure AnalysisGamma RaysMechanicsNitrogenOxygenPolyethylenesResins, SyntheticSterilizationTime Factors

Substanzen

Biocompatible MaterialsPolyethylenesResins, Syntheticultra-high molecular weight polyethyleneNitrogenOxygen

Autor:innen und Institutionen

  • Stryker Howmedica Osteonics Corporation, 300 Commerce Court, Mahwah, New Jersey 07430, USA. edidin@warwick.net.com

Zitieren

APA

Edidin, A. A., Herr, M. P., Villarraga, M. L., Muth, J., Yau, S. S., & Kurtz, S. M. (2002). Accelerated aging studies of UHMWPE. I. Effect of resin, processing, and radiation environment on resistance to mechanical degradation. Journal of Biomedical Materials Research, 61(2), 312-322. https://doi.org/10.1002/jbm.10135

Vancouver

Edidin AA, Herr MP, Villarraga ML, Muth J, Yau SS, Kurtz SM. Accelerated aging studies of UHMWPE. I. Effect of resin, processing, and radiation environment on resistance to mechanical degradation. Journal of Biomedical Materials Research. 2002;61(2):312-322. doi:10.1002/jbm.10135

BibTeX
@article{Edidin2002,
  author = {Edidin, A A and Herr, M P and Villarraga, M L and Muth, J and Yau, S S and Kurtz, S M},
  title = {Accelerated aging studies of UHMWPE. I. Effect of resin, processing, and radiation environment on resistance to mechanical degradation},
  journal = {Journal of Biomedical Materials Research},
  year = {2002},
  volume = {61},
  number = {2},
  pages = {312--322},
  doi = {10.1002/jbm.10135}
}
Kostenlos starten →