EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Scalable Jet‐Based Fabrication of PEI ‐Hydrogel Particles for CO 2 Capture

Jieke Jiang, Eline van Daatselaar, Hylke Wijnja, Tessa de Koning Gans, Michel Schellevis, Cornelis H. Venner, Derk W.F. Brilman, Claas Willem Visser

ENERGY & ENVIRONMENTAL MATERIALS · 2024-11 · 7 (6)

DOI: 10.1002/eem2.12748 ↗

Kurz gefasst

Fachartikel in der Zeitschrift ENERGY & ENVIRONMENTAL MATERIALS, online erschienen am 13.05.2024. Verfasst von Jieke Jiang und 7 weiteren Autor:innen. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 61 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Regional Development Fund.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The capture, regeneration, and conversion of CO 2 from ambient air and flue gas streams are critical aspects of mitigating global warming. Solid sorbents for CO 2 absorption are very promising as they have high mass transfer areas without energy input and reduce emissions and minimize corrosion as compared to liquid sorbents. However, precisely tunable solid CO 2 sorbents are difficult to produce. Here, we demonstrate the high‐throughput production of hydrogel‐based CO 2 ‐absorbing particles via liquid jetting. By wrapping a liquid jet consisting of an aqueous solution of cross‐linkable branched polyethylenimine (PEI) with a layer of suspension containing hydrophobic silica nanoparticles, monodisperse droplets with a silica nanoparticle coating layer was formed in the air. A stable Pickering emulsion containing PEI droplets was obtained after these ejected droplets were collected in a heated oil bath. The droplets turn into mm‐sized particles after thermal curing in the bath. The diameter, PEI content, and silica content of the particles were systematically varied, and their CO 2 absorption was measured as a function of time. Steam regeneration of the particles enabled cyclic testing, revealing a CO 2 absorption capacity of 6.5 ± 0.5 mol kg −1 solid PEI in pure CO 2 environments and 0.7 ± 0.3 mol kg −1 solid PEI for direct air capture. Several thousands of particles were produced per second at a rate of around 0.5 kg per hour, with a single nozzle. This process can be further scaled by parallelization. The complete toolbox for the design, fabrication, testing, and regeneration of functional hydrogel particles provides a powerful route toward novel solid sorbents for regenerative CO 2 capture.

Förderung

  • European Regional Development Fund

Zitieren

APA

Jiang, J., Daatselaar, E. V., Wijnja, H., Gans, T. D. K., Schellevis, M., Venner, C. H., Brilman, D. W., & Visser, C. W. (2024). Scalable Jet‐Based Fabrication of PEI ‐Hydrogel Particles for CO 2 Capture. ENERGY & ENVIRONMENTAL MATERIALS, 7(6). https://doi.org/10.1002/eem2.12748

Vancouver

Jiang J, Daatselaar EV, Wijnja H, Gans TDK, Schellevis M, Venner CH, et al. Scalable Jet‐Based Fabrication of PEI ‐Hydrogel Particles for CO 2 Capture. ENERGY & ENVIRONMENTAL MATERIALS. 2024;7(6). doi:10.1002/eem2.12748

BibTeX
@article{Jiang2024,
  author = {Jiang, Jieke and Daatselaar, Eline van and Wijnja, Hylke and Gans, Tessa de Koning and Schellevis, Michel and Venner, Cornelis H. and Brilman, Derk W.F. and Visser, Claas Willem},
  title = {Scalable Jet‐Based Fabrication of PEI ‐Hydrogel Particles for CO 2 Capture},
  journal = {ENERGY & ENVIRONMENTAL MATERIALS},
  year = {2024},
  volume = {7},
  number = {6},
  doi = {10.1002/eem2.12748}
}
Kostenlos starten →