EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of Different Application Modes of a Universal Adhesive System on the Bond Strength of Bulk‐Fill Composite Resin to Enamel and Dentin in Primary Teeth

Ali Nozari, Maryam Pakniyat Jahromi, Farnaz Haji Abbas Oghli, Zahra Jowkar iD, Seyed Ahmadreza Hamidi

Clinical and Experimental Dental Research · 2024

DOI: 10.1002/cre2.947 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical and Experimental Dental Research, 2024. Verfasst von Ali Nozari und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Pediatric Dentistry, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran. Hauptthemen laut MEDLINE: Composite Resins, Tooth, Deciduous, Dental Enamel, Dentin. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The authors received no specific funding for this work..

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

The objective of this study was to assess how the application mode of a universal adhesive system affects the microshear bond strength (μSBS) of bulk‐fill and conventional composite resins to enamel and dentin in primary teeth.

Methods

A total of 80 caries‐free primary second molars were randomly assigned to eight experimental groups ( n = 10) based on the bonding substrate (enamel or dentin), the application mode of the universal adhesive system (etch and rinse [E&R], or self‐etch [SE]), and the type of composite resin used (bulk‐fill or conventional). After bonding the composite resin to enamel or dentin, the μSBS of the bonded composite resins was measured.

Results

The mean μSBS value of bulk‐fill composite resin was significantly higher than that of conventional composite resin for both enamel and dentin substrates, regardless of the application mode ( p < 0.001). An interaction effect between the bonding substrate and the application mode of the adhesive system was observed, indicating a significant relationship ( p < 0.001). The highest μSBS values for primary teeth enamel were achieved using the E&R mode with bulk‐fill composite resin, while for dentin specimens, the SE mode with bulk‐fill composite resin yielded the highest μSBS values. The μSBS of the E&R group was significantly higher than that of the SE group for enamel specimens ( p < 0.001), whereas the μSBS of the SE group was significantly higher than that of the E&R group for dentin specimens ( p < 0.001).

Conclusion

Bulk‐fill composite resin demonstrated higher μSBS in comparison to conventional composite resin. The universal adhesive system exhibited superior performance in the SE mode compared to the E&R mode on primary dentin. Pre‐etching the enamel before the application of the universal adhesive enhanced the μSBS to primary teeth enamel, highlighting the importance of selectively acid etching the enamel of primary teeth.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Composite ResinsTooth, DeciduousDental EnamelDentinDental BondingHumansMolarMaterials TestingShear StrengthResin CementsDentin-Bonding AgentsDental Stress AnalysisIn Vitro Techniques

Stichwörter der Autor:innen

bulk‐fill composite resinprimary teethuniversal adhesive system

Substanzen

Composite ResinsResin CementsDentin-Bonding Agents

Autor:innen und Institutionen

  • Department of Pediatric Dentistry, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran.
  • Oral and Dental Disease Research Center, Department of Operative Dentistry, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran.
  • Department of Operative Dentistry, School of Dentistry, Shiraz University of Medical Sciences, Shiraz, Iran.

ORCID-Profile: Zahra Jowkar

Förderung

  • The authors received no specific funding for this work.

Zitieren

APA

Nozari, A., Pakniyat Jahromi, M., Haji Abbas Oghli, F., Jowkar, Z., & Hamidi, S. A. (2024). Influence of Different Application Modes of a Universal Adhesive System on the Bond Strength of Bulk‐Fill Composite Resin to Enamel and Dentin in Primary Teeth. Clinical and Experimental Dental Research. https://doi.org/10.1002/cre2.947

Vancouver

Nozari A, Pakniyat Jahromi M, Haji Abbas Oghli F, Jowkar Z, Hamidi SA. Influence of Different Application Modes of a Universal Adhesive System on the Bond Strength of Bulk‐Fill Composite Resin to Enamel and Dentin in Primary Teeth. Clinical and Experimental Dental Research. 2024. doi:10.1002/cre2.947

BibTeX
@article{Nozari2024,
  author = {Nozari, Ali and Pakniyat Jahromi, Maryam and Haji Abbas Oghli, Farnaz and Jowkar, Zahra and Hamidi, Seyed Ahmadreza},
  title = {Influence of Different Application Modes of a Universal Adhesive System on the Bond Strength of Bulk‐Fill Composite Resin to Enamel and Dentin in Primary Teeth},
  journal = {Clinical and Experimental Dental Research},
  year = {2024},
  doi = {10.1002/cre2.947}
}
Infokarte | EUVIMED

Artikeldaten derzeit nicht verfügbar.

Recherche