Comparison of Color Stability and Surface Roughness of Interim Crowns Fabricated by Conventional, Milling and 3D Printing Methods
Clinical and Experimental Dental Research · 2025
DOI: 10.1002/cre2.70119 ↗Kurz gefasst
Vergleichsstudie in der Zeitschrift Clinical and Experimental Dental Research, 2025. Verfasst von Zahra Hashemzade und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, Faculty of Dentistry, Shahed University, Tehran, Iran. Hauptthemen laut MEDLINE: Crowns, Printing, Three-Dimensional, Dental Prosthesis Design, Dental Restoration, Temporary. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The authors received no specific funding for this work..
Abstract (Originalsprache)
Objectives
Manufacturing temporary restorations is part of the treatment process in fixed prostheses, which is accomplished by different methods. The aim of this study is to compare the color stability and surface roughness of provisional crowns made by 3D printing, conventional and milling methods. Materials and Methods In this semi‐experimental study, 60 provisional crowns were created by conventional, milling, and 3D printing methods (20 samples for each method). Half of the samples in each group were treated with BisCover surface sealant after construction. The surface roughness was checked using a laser profilometer. To determine the color stability, an evaluation was done using a spectrophotometer on the first day and the second and fourth weeks after exposure to the tea solution, and ∆ E was calculated using L*a*b* values. Statistical analysis was performed at a significance level of 0.05.
Results
The surface roughness in the conventional group was significantly higher than in the milling group ( p < 0.05). The surface‐treated samples had less surface roughness and more color stability than other samples ( p < 0.05). ∆E in the 3D printing group was higher than other groups in all time intervals ( p < 0.05).
Conclusion
The milling method can be considered the best method of making provisional crowns in terms of color stability and surface smoothness. Also, the use of sealing materials can have a significant effect on improving color stability and surface smoothness in provisional crowns made by any method.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Prosthodontics, Faculty of Dentistry, Shahed University, Tehran, Iran.
ORCID-Profile: Zahra Mohammadi
Förderung
- The authors received no specific funding for this work.
Zitieren
APA
Hashemzade, Z., Alihemmati, M., Hakimaneh, S. M. R., Shayegh, S. S., Bafandeh, M. A., & Mohammadi, Z. (2025). Comparison of Color Stability and Surface Roughness of Interim Crowns Fabricated by Conventional, Milling and 3D Printing Methods. Clinical and Experimental Dental Research. https://doi.org/10.1002/cre2.70119
Vancouver
Hashemzade Z, Alihemmati M, Hakimaneh SMR, Shayegh SS, Bafandeh MA, Mohammadi Z. Comparison of Color Stability and Surface Roughness of Interim Crowns Fabricated by Conventional, Milling and 3D Printing Methods. Clinical and Experimental Dental Research. 2025. doi:10.1002/cre2.70119
BibTeX
@article{Hashemzade2025,
author = {Hashemzade, Zahra and Alihemmati, Mohammad and Hakimaneh, Seyed Mohammad Reza and Shayegh, Sayed Shojaedin and Bafandeh, Mohammad Amin and Mohammadi, Zahra},
title = {Comparison of Color Stability and Surface Roughness of Interim Crowns Fabricated by Conventional, Milling and 3D Printing Methods},
journal = {Clinical and Experimental Dental Research},
year = {2025},
doi = {10.1002/cre2.70119}
}
EUVIMED