EUVIMEDEUVIMED entdecken
Crossref

Tailoring hydrophobic PDMS – PVDF membranes via solvent–polymer compatibility and additives for membrane distillation desalination

Manish Singh Rajput, Sarita Kalla, Manish Vashishtha, Sushant Upadhyaya

The Canadian Journal of Chemical Engineering · 17.11.2026

DOI: 10.1002/cjce.70641 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Canadian Journal of Chemical Engineering, online erschienen am 17.11.2026. Verfasst von Manish Singh Rajput und 3 weiteren Autor:innen. Die Arbeit nennt 30 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Membrane wetting and limited operational stability remain major challenges in membrane distillation, and both are strongly influenced by solvent selection and phase‐inversion behaviour. In this study, the polymer–solvent compatibility of polyvinylidene fluoride (PVDF) and polydimethylsiloxane (PDMS) was evaluated using Hansen solubility parameter (HSP) distance analysis to guide the fabrication of solution‐blended PDMS–PVDF membranes. Four solvents—NMP, DMF, DMSO, and THF—were investigated. The HSP results indicated that NMP and DMF are compatible with PVDF, while THF exhibited stronger affinity for PDMS. Accordingly, PVDF was dissolved in NMP and DMF, and PDMS in THF. Additives, including PEG‐400, H 3 PO 4 , and toluene, were incorporated. NMP‐based membranes demonstrated higher hydrophobicity, with the PEG‐400‐modified membrane exhibiting a water contact angle of 104.3°, compared to 83.9° for the DMF‐based system. Membrane porosity ranged from 51.42% to 57.8%. AFM analysis revealed maximum surface roughness (Ra = 5.554 nm; Sq = 7.389 nm) for the PEG‐400‐modified membrane. SEM, XRD, and FTIR analyses confirmed favourable morphology and structural characteristics. During VMD desalination of a 20,000 mg L −1 NaCl solution, the permeate flux decreased from 18.5 to 17.6 kg m −2 h −1 over 180 h, while salt rejection remained approximately 99.77%. The selected membrane exhibited an LEP of approximately 294.5 kPa and a maximum thermal efficiency of 93.70%. The integration of HSP‐guided solvent screening, controlled additive comparison, solution blending, and long‐term VMD validation distinguishes this work from conventional solvent‐screening studies.

Zitieren

APA

Rajput, M. S., Kalla, S., Vashishtha, M., & Upadhyaya, S. (2026). Tailoring hydrophobic PDMS – PVDF membranes via solvent–polymer compatibility and additives for membrane distillation desalination. The Canadian Journal of Chemical Engineering. https://doi.org/10.1002/cjce.70641

Vancouver

Rajput MS, Kalla S, Vashishtha M, Upadhyaya S. Tailoring hydrophobic PDMS – PVDF membranes via solvent–polymer compatibility and additives for membrane distillation desalination. The Canadian Journal of Chemical Engineering. 2026. doi:10.1002/cjce.70641

BibTeX
@article{Rajput2026,
  author = {Rajput, Manish Singh and Kalla, Sarita and Vashishtha, Manish and Upadhyaya, Sushant},
  title = {Tailoring hydrophobic PDMS – PVDF membranes via solvent–polymer compatibility and additives for membrane distillation desalination},
  journal = {The Canadian Journal of Chemical Engineering},
  year = {2026},
  doi = {10.1002/cjce.70641}
}
Kostenlos starten →