EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Teaching Topology Optimization Through Polymer Material Extrusion Prototyping: A Transferable CAD‐CAE‐AM Framework With Numerical‐Experimental Validation

Natalia García‐Fernández, Diego Díaz‐Salamanca, Miguel Muñiz‐Calvente, David Blanco, Pelayo Fernández

Computer Applications in Engineering Education · 2026-11 · 34 (6)

DOI: 10.1002/cae.70291 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Computer Applications in Engineering Education, online erschienen am 06.11.2026. Verfasst von Natalia García‐Fernández und 4 weiteren Autor:innen. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universidad de Oviedo.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents a transferable computer‐aided engineering educational framework for teaching topology optimization through polymer material extrusion prototyping and numerical‐experimental validation. The framework is intended to help students move from idealized numerical simulation toward design decisions constrained by manufacturability, physical testing and failure interpretation. It is organized as a compact six‐stage workflow: material characterization and calibration, baseline structural simulation, topology optimization and verification, computer‐aided design reconstruction and design for additive manufacturing, controlled prototyping, and physical testing with redesign where needed. Its feasibility was examined through a master‐level implementation in which five student teams, distributed across two course editions, optimized and tested a pin‐loaded polymer component required to withstand 500 N. The implementation provides descriptive, team‐level evidence of technical feasibility and educational traceability. Student reports and prototypes documented material calibration, manufacturable reconstruction of topology‐optimization outputs, and experimental validation of final designs. All reported final designs exceeded the 500 N requirement, with measured final masses between 14.25 and 19.55 g and experimental failure loads between 740 and 1300 N. The tests also revealed bending and buckling in slender optimized members, showing that stress‐based topology optimization must be complemented with stability checks and physical validation. The study contributes a reproducible educational framework that closes the design‐simulate‐optimize‐manufacture‐test cycle within a compact laboratory structure.

Förderung

  • Universidad de Oviedo

Zitieren

APA

García‐Fernández, N., Díaz‐Salamanca, D., Muñiz‐Calvente, M., Blanco, D., & Fernández, P. (2026). Teaching Topology Optimization Through Polymer Material Extrusion Prototyping: A Transferable CAD‐CAE‐AM Framework With Numerical‐Experimental Validation. Computer Applications in Engineering Education, 34(6). https://doi.org/10.1002/cae.70291

Vancouver

García‐Fernández N, Díaz‐Salamanca D, Muñiz‐Calvente M, Blanco D, Fernández P. Teaching Topology Optimization Through Polymer Material Extrusion Prototyping: A Transferable CAD‐CAE‐AM Framework With Numerical‐Experimental Validation. Computer Applications in Engineering Education. 2026;34(6). doi:10.1002/cae.70291

BibTeX
@article{GarcaFernndez2026,
  author = {García‐Fernández, Natalia and Díaz‐Salamanca, Diego and Muñiz‐Calvente, Miguel and Blanco, David and Fernández, Pelayo},
  title = {Teaching Topology Optimization Through Polymer Material Extrusion Prototyping: A Transferable CAD‐CAE‐AM Framework With Numerical‐Experimental Validation},
  journal = {Computer Applications in Engineering Education},
  year = {2026},
  volume = {34},
  number = {6},
  doi = {10.1002/cae.70291}
}
Kostenlos starten →