EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Development of a Human Recombinant Collagen for Vat Polymerization‐Based Bioprinting

Domenic Schlauch iD, Jan Peter Ebbecke, Johanna Meyer, Tabea Marie Fleischhammer, Hamidreza Pirmahboub, Lutz Kloke, Selin Kara, Antonina Lavrentieva, Iliyana Pepelanova

Biotechnology Journal · 2024-10 · 19 (10)

DOI: 10.1002/biot.202400393 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Biotechnology Journal, online erschienen am 09.10.2024. Verfasst von Domenic Schlauch und 8 weiteren Autor:innen. Beteiligte Einrichtung: Cellbricks GmbH, Berlin, Germany. Hauptthemen laut MEDLINE: Bioprinting, Recombinant Proteins, Gelatin, Methacrylates. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 59 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In light‐based 3D‐bioprinting, gelatin methacrylate (GelMA) is one of the most widely used materials, as it supports cell attachment, and shows good biocompatibility and degradability in vivo. However, as an animal‐derived material, it also causes safety concerns when used in medical applications. Gelatin is a partial hydrolysate of collagen, containing high amounts of hydroxyproline. This causes the material to form a thermally induced gel at ambient temperatures, a behavior also observed in GelMA. This temperature‐dependent gelation requires precise temperature control during the bioprinting process to prevent the gelation of the material. To avoid safety concerns associated with animal‐derived materials and reduce potential issues caused by thermal gelation, a recombinant human alpha‐1 collagen I fragment was expressed in Komagataella phaffii without hydroxylation. The resulting protein was successfully modified with methacryloyl groups and underwent rapid photopolymerization upon ultraviolet light exposure. The developed material exhibited slightly slower polymerization and lower storage modulus compared to GelMA, while it showed higher stretchability. However, unlike the latter, the material did not undergo physical gelation at ambient temperatures, but only when cooled down to below 10°C, a characteristic that has not been described for comparable materials so far. This gelation was not caused by the formation of triple‐helical structures, as shown by the absence of the characteristic peak at 220 nm in CD spectra. Moreover, the developed recombinant material facilitated cell adherence with high cell viability after crosslinking via light to a 3D structure. Furthermore, desired geometries could be easily printed on a stereolithographic bioprinter.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

BioprintingRecombinant ProteinsGelatinMethacrylatesPolymerizationHumansPrinting, Three-DimensionalCollagen Type IBiocompatible MaterialsCollagenTemperatureAnimals

Stichwörter der Autor:innen

GelMArecombinant bioinkrecombinant gelatinthermal gelling

Substanzen

Recombinant ProteinsGelatinMethacrylatesCollagen Type IBiocompatible Materialsgelatin methacryloylCollagen

Autor:innen und Institutionen

  • Cellbricks GmbH, Berlin, Germany.
  • Leibniz University Hannover, Hannover, Germany.

ORCID-Profile: Domenic Schlauch

Zitieren

APA

Schlauch, D., Ebbecke, J. P., Meyer, J., Fleischhammer, T. M., Pirmahboub, H., Kloke, L., Kara, S., Lavrentieva, A., & Pepelanova, I. (2024). Development of a Human Recombinant Collagen for Vat Polymerization‐Based Bioprinting. Biotechnology Journal, 19(10). https://doi.org/10.1002/biot.202400393

Vancouver

Schlauch D, Ebbecke JP, Meyer J, Fleischhammer TM, Pirmahboub H, Kloke L, et al. Development of a Human Recombinant Collagen for Vat Polymerization‐Based Bioprinting. Biotechnology Journal. 2024;19(10). doi:10.1002/biot.202400393

BibTeX
@article{Schlauch2024,
  author = {Schlauch, Domenic and Ebbecke, Jan Peter and Meyer, Johanna and Fleischhammer, Tabea Marie and Pirmahboub, Hamidreza and Kloke, Lutz and Kara, Selin and Lavrentieva, Antonina and Pepelanova, Iliyana},
  title = {Development of a Human Recombinant Collagen for Vat Polymerization‐Based Bioprinting},
  journal = {Biotechnology Journal},
  year = {2024},
  volume = {19},
  number = {10},
  doi = {10.1002/biot.202400393}
}
Kostenlos starten →