EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Enhancing All‐Solid‐State Batteries Performance Through Thickness Control and Surface Passivation of Thermally Evaporated Lithium Metal Anodes

Jinsong Zhang iD, Linfeng Xu, Robin N Wullich iD, Thomas J Schmidt iD, Mario El Kazzi iD

Advanced Science · 2026-09 · 13 (54)

DOI: 10.1002/advs.76456 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Science, online erschienen am 13.07.2026. Verfasst von Jinsong Zhang und 4 weiteren Autor:innen. Beteiligte Einrichtung: PSI Center for Energy and Environmental Sciences, Paul Scherrer Institute, Villigen, Switzerland. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Hightech Zentrum Aargau AG and Forschungsfonds Aargau, Swiss National Science Foundation, Schweizerischer Nationalfonds zur Förderung der Wissenschaftlichen Forschung.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Thin lithium metal anodes are key to realizing high‐energy‐density and enhanced safety in all‐solid‐state batteries (ASSBs). However, extruded lithium foils below 50 µm suffer from poor structural integrity, rough surfaces, and resistive, native passivation layers, which limit cycling stability. In this study, thermally evaporated, high‐purity lithium with smooth grain‐boundary surface morphology significantly improves interfacial contact and electrochemical performance. Replacing extruded lithium with a 50 µm evaporated lithium anode increases the critical current density (CCD) from 1.6 to 2.1 mA cm −2 and enables 161 cycles at 1.5 mA cm −2 and 1.6 mAh cm −2 . A thickness‐dependence study reveals that maintaining a sufficient lithium reservoir is crucial to mitigate void formation and compensate for solid electrolyte interphase (SEI) growth. To overcome limitations at reduced thickness, an ultra‐thin 65 nm LiF passivation layer was applied to 25 µm evaporated lithium. The LiF coating suppresses chemical degradation during storage, stabilizes lithium/LPSCl interface, limits SEI growth, and mitigates dendrite, increasing the CCD to 2.6 mA cm −2 . In full cells, LiF‐coated 25 µm lithium delivers over 500 and 300 cycles at current densities of 1.5 and 3 mA cm −2 respectively. These results establish LiF‐passivated thermally evaporated lithium as a high‐performance anode design for next‐generation ASSBs.

Schlagwörter

Stichwörter der Autor:innen

all‐solid‐state batteriescycling performancelithium metal anodespassivation layerthermal evaporation

Autor:innen und Institutionen

  • PSI Center for Energy and Environmental Sciences, Paul Scherrer Institute, Villigen, Switzerland.
  • Institute For Molecular Physical Science, ETH Zurich, Zurich, Switzerland.

ORCID-Profile: Jinsong Zhang, Robin N Wullich, Thomas J Schmidt, Mario El Kazzi

Förderung

  • Hightech Zentrum Aargau AG and Forschungsfonds Aargau
  • Swiss National Science Foundation
  • Schweizerischer Nationalfonds zur Förderung der Wissenschaftlichen Forschung

Zitieren

APA

Zhang, J., Xu, L., Wullich, R. N., Schmidt, T. J., & Kazzi, M. E. (2026). Enhancing All‐Solid‐State Batteries Performance Through Thickness Control and Surface Passivation of Thermally Evaporated Lithium Metal Anodes. Advanced Science, 13(54). https://doi.org/10.1002/advs.76456

Vancouver

Zhang J, Xu L, Wullich RN, Schmidt TJ, Kazzi ME. Enhancing All‐Solid‐State Batteries Performance Through Thickness Control and Surface Passivation of Thermally Evaporated Lithium Metal Anodes. Advanced Science. 2026;13(54). doi:10.1002/advs.76456

BibTeX
@article{Zhang2026,
  author = {Zhang, Jinsong and Xu, Linfeng and Wullich, Robin N and Schmidt, Thomas J and Kazzi, Mario El},
  title = {Enhancing All‐Solid‐State Batteries Performance Through Thickness Control and Surface Passivation of Thermally Evaporated Lithium Metal Anodes},
  journal = {Advanced Science},
  year = {2026},
  volume = {13},
  number = {54},
  doi = {10.1002/advs.76456}
}
Kostenlos starten →