EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries

Qian Xia, Shuoguo Yuan iD, Qiang Zhang, Can Huang, Jun Liu, Hongyun Jin

Advanced Science · 2024-08 · 11 (29)

DOI: 10.1002/advs.202401453 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Science, online erschienen am 03.06.2024. Verfasst von Qian Xia und 5 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Materials Science and Chemistry, China University of Geosciences, Wuhan, 430074, China. Die Arbeit wurde bisher 40-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key Research and Development Program of China, Guangdong Basic and Applied Basic Research Foundation, New Faculty Startup Fund of China University of Geosciences.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) is one of the most attractive solid‐state electrolytes (SSEs) for application in all‐solid‐state lithium batteries (ASSLBs) due to its advantages of high ionic conductivity, air stability and low cost. However, the poor interfacial contact and slow Li‐ion migration have greatly limited its practical application. Herein, a composite ion‐conducting layer is designed at the Li/LATP interface, which a MoS 2 film is constructed on LATP via chemical vapor deposition, followed by the introduction of a solid polymer (SP) liquid precursor to form a MoS 2 @SP protective layer. This protective layer not only achieves a lower Li‐ion migration energy barrier, but also adsorbs more Li‐ion, which is able to promote interfacial ion transport and improve interfacial contacts. Thanks to the improved migration and adsorption of Li‐ion, the Li symmetric cell containing LATP‐MoS 2 @SP exhibits a stable cycle of more than 1200 h at 0.1 mA cm −2 . More remarkably, the capacity retention of the full cell assembled with LiFePO 4 cathode is as high as 86.2% after 400 cycles at 1 C. This work provides a design strategy for significantly improving unstable interfaces of SSEs and realizing high‐performance ASSLBs.

Schlagwörter

Stichwörter der Autor:innen

LATPMoS2interfacesolid‐state electrolytessolid‐state lithium batteries

Autor:innen und Institutionen

  • Faculty of Materials Science and Chemistry, China University of Geosciences, Wuhan, 430074, China.
  • Guangdong Provincial Key Laboratory of Advanced Energy Storage Materials, School of Materials Science and Engineering, South China University of Technology, Guangzhou, 510641, China.

ORCID-Profile: Shuoguo Yuan

Förderung

  • National Key Research and Development Program of China
  • Guangdong Basic and Applied Basic Research Foundation
  • New Faculty Startup Fund of China University of Geosciences

Zitieren

APA

Xia, Q., Yuan, S., Zhang, Q., Huang, C., Liu, J., & Jin, H. (2024). Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries. Advanced Science, 11(29). https://doi.org/10.1002/advs.202401453

Vancouver

Xia Q, Yuan S, Zhang Q, Huang C, Liu J, Jin H. Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries. Advanced Science. 2024;11(29). doi:10.1002/advs.202401453

BibTeX
@article{Xia2024,
  author = {Xia, Qian and Yuan, Shuoguo and Zhang, Qiang and Huang, Can and Liu, Jun and Jin, Hongyun},
  title = {Designing the Interface Layer of Solid Electrolytes for All‐Solid‐State Lithium Batteries},
  journal = {Advanced Science},
  year = {2024},
  volume = {11},
  number = {29},
  doi = {10.1002/advs.202401453}
}
Kostenlos starten →